Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Engine control module (ecm) i/o signal Electrical specification

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Engine control module (ecm) i/o signal Electrical specification

ENGINE (DIAGNOSTICS)(H4DO) > Engine Control Module (ECM) I/O Signal

ELECTRICAL SPECIFICATION

1. ENGINE CONTROL MODULE (ECM)

    Description

    Connector No.

    Terminal No.

    Signal (V)

    Note

    Ignition SW ON

    (Engine OFF)

    Engine ON

    (Idling)

    Crankshaft position sensor

    (+) signal

    B136

    16

    5

    0 or 5

    Waveform*

    (−) signal

    B136

    27

    0

    0

    Front oxygen (A/F) sensor

    (+) signal

    B136

    19

    2.8 — 3.2

    2.8 — 3.2

    (−) signal

    B136

    18

    2.4 — 2.7

    2.4 — 2.7

    Rear oxygen sensor

    Signal

    B136

    21

    0

    0 — 0.9

    Front oxygen (A/F) sensor heater signal

    B136

    5

    Battery voltage

    0 or battery voltage

    Waveform

    Rear oxygen sensor heater signal

    B134

    6

    Battery voltage

    0 or battery voltage

    Waveform

    Oxygen sensor

    Shield

    B136

    30

    0

    0

    Engine coolant temperature sensor

    Signal

    B134

    30

    1 — 1.4

    1 — 1.6

    Air flow sensor

    Signal

    B137

    22

    0.3 — 4.5

    Shield

    B137

    28

    0

    0

    Ground

    B137

    29

    0

    0

    Intake air temperature sensor signal

    B137

    12

    0.3 — 4.6

    0.3 — 4.6

    Engine oil temperature sensor signal

    B134

    20

    1 — 1.4

    1 — 1.6

    Starter switch

    B137

    17

    Waveform

    Waveform

    Model without push button start: Waveform

    Models with push button start: Waveform

    Accessory cut request

    B135

    32

    Waveform

    Waveform

    Model without push button start: Waveform

    Models with push button start: Waveform

    Starter switch 2

    B137

    14

    Waveform

    Waveform

    Model without push button start: Waveform

    Models with push button start: Waveform

    Starter cut relay

    B135

    34

    Waveform

    Waveform

    Model without push button start: Waveform

    Models with push button start: Waveform

    Ignition switch

    B137

    27

    Battery voltage

    Battery voltage

    Neutral position switch

    B137

    16

    ON: 0

    OFF: Battery voltage

    ON: 0

    OFF: Battery voltage

    Delivery mode switch

    B137

    13

    Battery voltage

    Battery voltage

    When fuse is installed: 0

    Knock sensor

    Signal

    B136

    28

    2.5

    2.5

    Shield

    B136

    29

    0

    0

    Back-up power supply

    B137

    2

    Battery voltage

    Battery voltage

    Control module power supply

    B136

    6

    Battery voltage

    Battery voltage

    B137

    1

    Battery voltage

    Battery voltage

    Sensor power supply

    B134

    19

    5

    5

    B135

    22

    5

    5

    Ignition control

    #1

    B134

    21

    0

    0 or 5

    Waveform

    #2

    B134

    10

    0

    0 or 5

    Waveform

    #3

    B134

    31

    0

    0 or 5

    Waveform

    #4

    B134

    8

    0

    0 or 5

    Waveform

    Fuel injector

    #1

    B134

    12

    Battery voltage

    0 or battery voltage

    Waveform

    #2

    B134

    22

    Battery voltage

    0 or battery voltage

    Waveform

    #3

    B134

    32

    Battery voltage

    0 or battery voltage

    Waveform

    #4

    B134

    13

    Battery voltage

    0 or battery voltage

    Waveform

    Fuel pump relay control

    B135

    19

    Battery voltage

    ON: 0.5 or less

    OFF: Battery voltage

    A/C relay control

    B135

    35

    ON: 0.5 or less

    OFF: Battery voltage

    ON: 0.5 or less

    OFF: Battery voltage

    A/C switch

    B137

    26

    ON: Battery voltage

    OFF: 0

    ON: Battery voltage

    OFF: 0

    Manual A/C model

    Blower fan switch

    B137

    20

    ON: 0

    OFF: Battery voltage

    ON: 0

    OFF: Battery voltage

    Manual A/C model

    A/C middle pressure switch

    B137

    8

    ON: 0

    OFF: Battery voltage

    ON: 0

    OFF: Battery voltage

    Main fan relay control

    B135

    12

    ON: 0.5 or less

    OFF: Battery voltage

    ON: 0.5 or less

    OFF: Battery voltage

    Sub fan relay control

    B135

    11

    ON: 0.5 or less

    OFF: Battery voltage

    ON: 0.5 or less

    OFF: Battery voltage

    Engine speed output

    B135

    15

    0 or battery voltage

    Waveform

    Purge control solenoid valve

    B134

    11

    Battery voltage

    Battery voltage

    When in operation: 0 or battery voltage

    EGR control valve

    Signal 1

    B136

    11

    Battery voltage

    0 or battery voltage

    Signal 2

    B136

    13

    Battery voltage

    0 or battery voltage

    Signal 3

    B136

    31

    Battery voltage

    0 or battery voltage

    Signal 4

    B136

    32

    Battery voltage

    0 or battery voltage

    Manifold absolute pressure sensor signal

    B136

    20

    3.4 — 3.8

    1 — 1.6

    Electronic throttle control

    Main signal

    B134

    18

    Approx. 0.7

    Approx. 0.6 — 0.7

    Fully closed: Approx. 0.6

    Fully open: Approx. 4.0

    Sub signal

    B134

    28

    Approx. 1.6

    Approx. 1.5 — 1.6

    Fully closed: Approx. 1.5

    Fully open: Approx. 4.2

    Electronic throttle control motor (+)

    B134

    2

    Duty waveform

    Duty waveform

    Drive frequency: 500 Hz

    Electronic throttle control motor (−)

    B134

    1

    Duty waveform

    Duty waveform

    Drive frequency: 500 Hz

    Electronic throttle control motor power supply

    B135

    7

    Battery voltage

    Battery voltage

    Electronic throttle control motor relay

    B135

    17

    0

    0

    Intake oil control solenoid RH

    B134

    17

    Battery voltage

    0 or battery voltage

    Waveform

    Intake oil control solenoid LH

    B134

    16

    Battery voltage

    0 or battery voltage

    Waveform

    Exhaust oil control solenoid RH

    B134

    7

    Battery voltage

    0 or battery voltage

    Waveform

    Exhaust oil control solenoid LH

    B134

    5

    Battery voltage

    0 or battery voltage

    Waveform

    Intake camshaft position sensor RH

    B136

    26

    0 or 5

    0 or 5

    Waveform*

    Intake camshaft position sensor LH

    B136

    15

    0 or 5

    0 or 5

    Waveform*

    Exhaust camshaft position sensor RH

    B136

    14

    0 or 5

    0 or 5

    Waveform*

    Exhaust camshaft position sensor LH

    B136

    25

    0 or 5

    0 or 5

    Waveform*

    Camshaft position sensor ground

    B136

    34

    0

    0

    Accelerator pedal position sensor

    Main signal

    B135

    23

    Fully closed: 0.4 — 1

    Fully opened: 2.4 — 3.7

    Fully closed: 0.4 — 1

    Fully opened: 2.4 — 3.7

    Main power supply

    B135

    21

    5

    5

    Ground

    (main)

    B135

    29

    0

    0

    Sub signal

    B135

    31

    Fully closed: 0.3 — 1.1

    Fully opened: 2.3 — 3.8

    Fully closed: 0.3 — 1.1

    Fully opened: 2.3 — 3.8

    Starter relay

    B135

    26

    Waveform

    Waveform

    Model without push button start: Waveform

    Models with push button start: Waveform

    Clutch switch

    B137

    15

    ON: 0

    OFF: Battery voltage

    ON: 0

    OFF: Battery voltage

    Brake switch 1

    (Brake switch)

    B137

    7

    When brake pedal is depressed: 0

    When brake pedal is released: Battery voltage

    When brake pedal is depressed: 0

    When brake pedal is released: Battery voltage

    Brake switch 2

    (Stop light switch)

    B137

    3

    When brake pedal is depressed: Battery voltage

    When brake pedal is released: 0

    When brake pedal is depressed: Battery voltage

    When brake pedal is released: 0

    Cruise control command switch

    B137

    30

    When operating nothing: 3.5 — 4.5

    When operating RES/ACC: 2.5 — 3.5

    When operating SET/COAST: 0.5 — 1.5

    When operating CANCEL: 0 — 0.5

    When operating nothing: 3.5 — 4.5

    When operating RES/ACC: 2.5 — 3.5

    When operating SET/COAST: 0.5 — 1.5

    When operating CANCEL: 0 — 0.5

    Cruise control main switch

    B137

    23

    ON: 0

    OFF: 5

    ON: 0

    OFF: 5

    CAN communication

    (MAIN-CAN)

    (Hi)

    B137

    19

    (Lo)

    B137

    18

    Self-shutoff control

    B135

    13

    0

    0

    Electrical component location Location
    ENGINE (DIAGNOSTICS)(H4DO) > Electrical Component LocationLOCATION1. CONTROL MODULE(1)Engine control module (ECM)(3)Malfunction indicator light(4)Data link connector(2)Delivery (test) mode fuse ...

    General diagnostic table Inspection
    ENGINE (DIAGNOSTICS)(H4DO) > General Diagnostic TableINSPECTION1. ENGINENOTE:Malfunction of parts other than those listed is also possible. Engine Trouble in General">SymptomsFaulty parts1 ...

    Other materials:

    Assembly
    REAR SUSPENSION > Rear Lateral LinkASSEMBLY1. Before assembly, inspect the following items and replace any faulty part with a new one.• Visually check the lateral link assembly - rear for damage and deformation.• Visually check the bushing for abnormal cracks, fatigue or damage.2. Usi ...

    Inspection
    MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Reverse Idler GearINSPECTION1. Move the reverse shifter rod toward the reverse side. Check the clearance between the reverse idler gear and the transmission case wall surface.If the value is out of specification, select the appropriate reverse shifter l ...

    Read cancel code Operation
    CRUISE CONTROL SYSTEM (DIAGNOSTICS) > Read Cancel CodeOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. On «Select System» display, sele ...

    © 2016-2024 Copyright www.sucross.com