Subaru Crosstrek Service Manual: Electrical specification
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Control Module I/O Signal
ELECTRICAL SPECIFICATION
• Models without EyeSight
NOTE:
• Terminal numbers in VDCCM&H/U connector (on the control module side) are shown in the figure.
• When the connector is removed from the VDCCM&H/U, the brake warning light (EBD warning light), ABS warning light, VDC warning light & VDC indicator light, VDC OFF indicator light, and the hill start assist warning light illuminate.
Content | Terminal No. (+) — (−) | Input/Output signal | ||
Measured value and measuring conditions | ||||
Power supply | 28 — 38 | 10 — 15 V when the ignition switch is ON. | ||
ABS wheel speed sensor | Front LH wheel | Power supply | 19 — 38 | 0 — 18 V when the ignition switch is ON. |
Signal | 8 | 7 — 14 mA: Rectangle waveform | ||
Front RH wheel | Power supply | 16 — 38 | 0 — 18 V when the ignition switch is ON. | |
Signal | 4 | 7 — 14 mA: Rectangle waveform | ||
Rear LH wheel | Power supply | 31 — 38 | 0 — 18 V when the ignition switch is ON. | |
Signal | 18 | 7 — 14 mA: Rectangle waveform | ||
Rear RH wheel | Power supply | 17 — 38 | 0 — 18 V when the ignition switch is ON. | |
Signal | 29 | 7 — 14 mA: Rectangle waveform | ||
Valve relay power supply | 25 — 38 | 10 — 15 V | ||
Motor relay power supply | 1 — 13 | 10 — 15 V | ||
Stop light switch | 30 — 38 | 1.5 V or less when the stop light is OFF; 10 — 15 V when the stop light is ON. | ||
Vehicle speed output signal | 2 | 0 ←> 12 V pulse | ||
VDC OFF switch | 12 — 38 | 1 ? or less when the OFF switch is “ON”; 1 M? or more when the switch is “OFF”. | ||
CAN communication line (H) | 26 | Pulse signal | ||
CAN communication line (L) | 14 | Pulse signal | ||
Ground | 38 | — | ||
Ground | 13 | — | ||
• Models with EyeSight
NOTE:
• Terminal numbers in VDCCM&H/U connector (on the control module side) are shown in the figure.
• When the connector is removed from the VDCCM&H/U, the brake warning light (EBD warning light), ABS warning light, VDC warning light & VDC indicator light, VDC OFF indicator light, and the hill start assist warning light illuminate.
Content | Terminal No. (+) — (−) | Input/Output signal | ||
Measured value and measuring conditions | ||||
Power supply | 20 — 26 | 10 — 15 V when the ignition switch is ON. | ||
ABS wheel speed sensor | Front LH wheel | Power supply | 9 — 26 | 0 — 18 V when the ignition switch is ON. |
Signal | 8 | 7 — 14 mA: Rectangle waveform | ||
Front RH wheel | Power supply | 5 — 26 | 0 — 18 V when the ignition switch is ON. | |
Signal | 6 | 7 — 14 mA: Rectangle waveform | ||
Rear LH wheel | Power supply | 3 — 26 | 0 — 18 V when the ignition switch is ON. | |
Signal | 2 | 7 — 14 mA: Rectangle waveform | ||
Rear RH wheel | Power supply | 11 — 26 | 0 — 18 V when the ignition switch is ON. | |
Signal | 12 | 7 — 14 mA: Rectangle waveform | ||
Valve relay power supply | 1 — 26 | 10 — 15 V | ||
Motor relay power supply | 14 — 26 | 10 — 15 V | ||
Stop light switch | 16 — 26 | 1.5 V or less when the stop light is OFF; 10 — 15 V when the stop light is ON. | ||
Subaru Select Monitor | 18 — 26 | 0 ←> 12 V pulse (during the communication) | ||
Vehicle speed output signal | 24 | 0 ←> 12 V pulse | ||
VDC OFF switch | 22 — 26 | 0.5 ? or less when the OFF switch is ON; 1 M? or more when the switch is OFF. | ||
CAN communication line (H) | 23 | Pulse signal | ||
CAN communication line (L) | 21 | Pulse signal | ||
Ground | 26 | — | ||
Wiring diagram
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Control Module I/O SignalWIRING DIAGRAMRefer to “Vehicle Dynamics Control System” in the wiring diagram. Vehicle Dynamics Control System& ...
Other materials:
Disassembly
CLUTCH SYSTEM > Master CylinderDISASSEMBLY1. Remove the straight pin and nipple.(A)Nipple(B)Straight pin2. Remove the oil seal.(A)Oil seal3. Move the seat towards the rear.(A)Seat(B)Master cylinder4. Remove the piston stop ring.CAUTION:When removing the piston stop ring, be careful to prevent the ...
Dtc p1495 coil 2 egr "a" control circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P1495 COIL 2 EGR "A" CONTROL CIRCUIT HIGHNOTE:For the diagnostic procedure, refer to DTC P1499. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P1499 COIL 4 EGR "A" CONTRO ...
Removal
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Control Valve BodyREMOVALCAUTION:• Directly after the vehicle has been running or the engine has been idling for a long time, the CVTF is hot. Be careful not to burn yourself.• Be careful not to spill CVTF on the exhaust pipe to prevent it f ...
