Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Electrical specification

EyeSight (DIAGNOSTICS) > Control Module I/O Signal

ELECTRICAL SPECIFICATION

1. STEREO CAMERA

Terminal No.

Content

Measuring condition

Standard

(R137) No. 1

(R137) No. 2

(R137) No. 3

(R137) No. 4

(R137) No. 5

(R137) No. 6 ←> Chassis ground

Ignition power supply

Ignition switch OFF > ON

Less than 1 V > 9 — 16 V

(R137) No. 7 ←> Chassis ground

GND

Always

Less than 1 ?

(R137) No. 8 ←> Chassis ground

Battery power supply

Always

9 — 16 V

(R137) No. 9 ←> Chassis ground

CAN L

Always

1 k? or more

(R137) No. 10 ←> Chassis ground

CAN H

Always

1 k? or more

(R137) No. 11

(R137) No. 12 ←> Chassis ground

Pre-collision brake OFF switch input

Pre-collision brake OFF switch OFF > ON

Approx. 1 k? > less than 1 ?

(R137) No. 13 ←> Chassis ground

Lane departure warning OFF switch input

Lane departure warning OFF switch OFF > ON

Approx. 1 k? > less than 1 ?

(R137) No. 14 ←> (R137) No. 15

EyeSight steering switch input

ALL OFF (no switch operation)

3.6 V — 4.5 V

ALL OFF > RES/+ ON

2.6 V — 3.5 V

ALL OFF > following distance ON

3.6 V — 4.5 V

ALL OFF > SET/− ON

0.6 V — 1.5 V

ALL OFF > CRUISE ON

0.0 V — 0.5 V

(R137) No. 15 ←> Chassis ground

EyeSight steering switch GND

Always

Less than 1 ?

(R137) No. 16 ←> (R137) No. 15

EyeSight steering switch input

ALL OFF (no switch operation)

2.6 V — 5.0 V

ALL OFF > RES/+ ON

2.6 V — 5.0 V

ALL OFF > following distance ON

0.0 V — 2.5 V

ALL OFF > SET/− ON

2.6 V — 5.0 V

ALL OFF > CRUISE ON

2.6 V — 5.0 V

2. ENGINE CONTROL MODULE (ECM)

For details on the input/output signals for the engine control module, refer to ENGINE (DIAGNOSTICS). Engine Control Module (ECM) I/O Signal">

3. VDC CONTROL MODULE (VDCCM)

For details on the input/output signals for VDC control module, refer to VDC (DIAGNOSTICS). Control Module I/O Signal > ELECTRICAL SPECIFICATION">

4. TRANSMISSION CONTROL MODULE (TCM)

For details on the input/output signals for the transmission control module, refer to AUTOMATIC TRANSMISSION (DIAGNOSTICS). Transmission Control Module (TCM) I/O Signal">

5. BODY INTEGRATED UNIT

Refer to the BODY CONTROL SYSTEM (DIAGNOSTICS) for the I/O Signal of the body integrated unit. Control Module I/O Signal > ELECTRICAL SPECIFICATION">

6. COMBINATION METER

For details on the input/output signals for the combination meter, refer to INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS). Control Module I/O Signal > ELECTRICAL SPECIFICATION">

7. MFD

For details on the input/output signals for MFD, refer to INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS). Control Module I/O Signal > ELECTRICAL SPECIFICATION">

Control module i/o signal
...

System block diagram
EyeSight (DIAGNOSTICS) > Control Module I/O SignalSYSTEM BLOCK DIAGRAMMain signals used between stereo camera and relevant CM*: With high grade MFD only ...

Other materials:

Control screen
PHONE (Menu) screen PHONE (Dialpad) screen Open the "Incoming Calls" screen. Refer to "By incoming calls" Open the "Outgoing Calls" screen. Refer to "By outgoing calls" Open the "Contacts" screen. Refer to "By contacts list Open the dialpad screen. Refer to "By Dialpad O ...

Inspection
SPEED CONTROL SYSTEMS(H4DO) > Accelerator PedalINSPECTION1. CHECK ACCELERATOR PEDAL SENSOR AREA (METHOD WITH CIRCUIT TESTER)1. Remove the glove box. Glove Box > REMOVAL">2. Turn the ignition switch to ON. (Engine OFF)3. Measure the voltage between ECM connector terminals.• Main ...

Removal
MECHANICAL(H4DO) > Crank PulleyREMOVALNOTE:When replacing a single part, perform the work with the engine assembly installed to body.1. When working on the vehicleNOTE:When working on the vehicle, perform the following steps also.(1) Remove the radiator main fan & fan motor assembly and radia ...

© 2016-2024 Copyright www.sucross.com