VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Warning Light Illumination Pattern
EBD WARNING LIGHT, ABS WARNING, VDC OFF INDICATOR LIGHT, VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT COME ON
Detecting condition:
Defective combination meter
Trouble symptom:
When the ignition switch is turned to ON (engine OFF), EBD warning light, ABS warning light, VDC OFF indicator light, and VDC warning light & VDC indicator light do not illuminate.
NOTE:
When pressing the VDC OFF switch for 10 seconds or more, the VDC OFF indicator light goes off and cannot operate any more. When turning the ignition switch from OFF to ON, the OFF operation enabled status is restored.
STEP | CHECK | YES | NO |
1.CHECK OTHER INDICATOR LIGHT.
Turn the ignition switch to ON.
Immediately after the ignition switch is turned to ON, do all the indicator lights for VDC system and others illuminate?
Warning Light Illumination Pattern > EBD WARNING LIGHT, ABS WARNING, VDC OFF INDICATOR LIGHT, VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT COME ON">Go to Step 2.
Check the combination meter. Combination Meter System > OPERATION">
2.CHECK VDCCM.
When the engine does not start, display the current data of VDCCM using Subaru Select Monitor.
Immediately after the ignition switch is turned to ON, is the «EBD Warning Light» ON?
Warning Light Illumination Pattern > EBD WARNING LIGHT, ABS WARNING, VDC OFF INDICATOR LIGHT, VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT COME ON">Go to Step 3.
• Models without EyeSight
Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">
• Models with EyeSight
Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">
3.CHECK VDCCM.
When the engine does not start, display the current data of VDCCM using Subaru Select Monitor.
Immediately after the ignition switch is turned to ON, is the «ABS Warning Lamp» ON?
Warning Light Illumination Pattern > EBD WARNING LIGHT, ABS WARNING, VDC OFF INDICATOR LIGHT, VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT COME ON">Go to Step 4.
• Models without EyeSight
Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">
• Models with EyeSight
Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">
4.CHECK VDCCM.
When the engine does not start, display the current data of VDCCM using Subaru Select Monitor.
Immediately after the ignition switch is turned to ON, is the «VDC Warning Lamp» ON?
Check the combination meter. Combination Meter System > OPERATION">
• Models without EyeSight
Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">
• Models with EyeSight
Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">
Removal
REAR SUSPENSION > Rear Lateral LinkREMOVAL1. Disconnect the ground cable from battery. NOTE">2. Lift up the vehicle, and then remove the rear wheels.3. Remove the sensor assembly - headlight beam leveler. (Model with auto headlight beam leveler, left side only)CAUTION:Do not apply impact ...
Dtc b2223 gerda malfunction
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2223 GERDA MALFUNCTIONDTC DETECTING CONDITION:When the system microcomputer can not send/receive the data with the image microcomputer normally.TROUBLE SYMPTOM:There is no display on the TFT. O ...
Steering switches for audio
Some parts of the audio/visual system can
be adjusted using the switches on the
steering wheel.
+ − switch
switch
Mute/Enter switch
List switch
Back switch
Source switch
+/− switch
Mode
Operation
Function
Except list screen
Press
V ...