LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC U1433 INVALID DATA RECEIVED FROM EyeSight
DTC DETECTING CONDITION:
Defective data was transmitted from stereo camera.
TROUBLE SYMPTOM:
Cooperation control of EyeSight does not operate properly.
STEP | CHECK | YES | NO |
1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.
Was the basic diagnostic procedure performed up to STEP 3?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 2.
Perform the basic diagnostic procedure. Basic Diagnostic Procedure">
2.CHECK DTC.
Check the displayed DTC.
Are DTCs other than U*** displayed?
Perform the diagnosis according to DTC.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 3.
3.CHECK DTC.
Check the displayed DTC.
Is DTC for the bus off or the data no-receive displayed?
Perform the diagnosis according to DTC.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 4.
4.CHECK DTC.
Check the displayed DTC.
Is U1433 a current malfunction?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 5.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 9.
5.CHECK DTC.
1) Turn the ignition switch to OFF.
2) Disconnect the stereo camera connector.
3) Connect the disconnected connectors.
4) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is U1433 a current malfunction?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 6.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 9.
6.CHECK DTC.
Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">
Is the EyeSight data abnormal detected in several modules?
Replace the stereo camera. Stereo Camera">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 7.
7.REPLACE MODULE.
1) Replace the stereo camera.
2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is U1433 a current malfunction?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 8.
System is normal.
8.CHECK MODULE.
1) Reinstall the stereo camera.
2) Replace the module that the DTC has been detected.
3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is U1433 a current malfunction?
Replace the stereo camera. Stereo Camera">
System is normal.
9.CHECK HARNESS.
1) Shake the harness, and check for poor contact.
2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">
Is U1433 a current malfunction?
Repair the poor contact of harness, or replace the harness.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1433 INVALID DATA RECEIVED FROM EyeSight">Go to Step 10.
10.CHECK CONNECTOR.
Check the connector used for high speed CAN for poor contact.
Is there poor contact of connector?
Repair the connector that has poor contact, or replace harness.
It is possible that temporary poor communication occurs. Delete the DTC.
Removal
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Air Vent GrilleREMOVAL1. CENTER GRILLE ASSEMBLYCAUTION:• Do not put your finger on the fin of the air vent grille. Doing so may damage the fin.• Always pull the center grille assembly toward you slowly. If attempting to remove by turning it u ...
Shift lock release
If the select lever cannot be operated, turn
the ignition switch back to the "ON"
position then move the select lever to the
"P" position with the select lever button
pressed and brake pedal depressed.
If the select lever does not move after
performing the above procedure, perform
the follo ...
Map lights
Type A
Type B
To turn on the map light, push the switch.
To turn it off, push the switch again.
NOTE
For the type A map lights, although the
light switches are in the ON position,
the lights are automatically turned off
after approximately 30 seconds of
illumination to prevent the veh ...