Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc u1201 can-hs counter abnormal

LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC U1201 CAN-HS COUNTER ABNORMAL

DTC DETECTING CONDITION:

Communication is unstable because of high speed CAN communication error.

TROUBLE SYMPTOM:

Display of combination meter indicates faulty.

Control faulty may occur due to CAN communication error.

STEPCHECKYESNO

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1201 CAN-HS COUNTER ABNORMAL">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

1) Start the engine.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U0073 a current malfunction?

Perform the diagnosis of U0073. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0073 CONTROL MODULE COMMUNICATION BUS OFF">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1201 CAN-HS COUNTER ABNORMAL">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U1201 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1201 CAN-HS COUNTER ABNORMAL">Go to Step 4.

It is possible that temporary poor communication occurs. Perform the clear memory. Clear Memory Mode">

4.CHECK DTC.

1) Turn the ignition switch to ON.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U1201 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U1201 CAN-HS COUNTER ABNORMAL">Go to Step 5.

It is possible that temporary poor communication occurs. Perform the clear memory. Clear Memory Mode">

5.CHECK CONTROL MODULE.

1) Turn the ignition switch to OFF.

2) Disconnect the control modules other than body integrated unit in order.

NOTE:

When disconnecting ECM or VDC CM, connect resistance of 120 ? between CAN Hi and CAN Lo as an alternative of end resistance.

3) Turn the ignition switch to ON.

4) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is there any control module that U1201 is not detected as current malfunction?

Replace the control module.

Repeat 1) to 4) in step 5 until U1201 is not detected.

Dtc u1120 lost communication with autostart stop control module
LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U1120 LOST COMMUNICATION WITH AUTOSTART STOP CONTROL MODULENOTE:The electric power steering CM identifies wheth ...

Dtc u1235 lost communication with eyesight
LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U1235 LOST COMMUNICATION WITH EyeSightDTC DETECTING CONDITION:No data from stereo camera is received.TROUBLE SY ...

Other materials:

Relay and fuse
Inspection CRUISE CONTROL SYSTEM > Relay and FuseINSPECTION1. CHECK FUSE1. Remove the fuse and inspect visually.2. If the fuse is blown out, replace the fuse.NOTE:If the fuse is blown again, check the system wiring harness. Location CRUISE CONTROL SYSTEM > Relay and FuseLOCATIONRelay & f ...

Inspection
FRONT SUSPENSION > Front StrutINSPECTIONCheck the removed part for wear, damage and cracks, and then repair or replace it if defective.1. STRUT1. Check for oil leaks.2. Move the piston rod up and down to check that it operates smoothly without any hitch.3. Check the piston rod runout.Preparation ...

Inspection
SEAT BELT SYSTEM > Rear Seat BeltINSPECTION1. VISUAL INSPECTIONCheck for the following, and replace with new parts if necessary.• Seat belt is slackened, bent or worn.• Seat belt is abnormally wound or extended.• Seat belt inner - rear is deformed or damaged.• Seat belt bu ...

© 2016-2024 Copyright www.sucross.com