Subaru Crosstrek Service Manual: Dtc u0422 invalid data received from body control module

DTC DETECTING CONDITION:

Defective data was transmitted from body integrated unit.

TROUBLE SYMPTOM:

Cooperation control with body integrated unit does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is DTC for the bus off or the data no-receive displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 4.

4.CHECK DTC.

Check the displayed DTC.

Is U0422 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 9.

5.CHECK DTC.

1) Turn the ignition switch to OFF.

2) Disconnect the body integrated unit connector.

3) Connect the disconnected connectors.

4) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0422 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 9.

6.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the body integrated data abnormal detected in several modules?

Replace the body integrated unit. Body Integrated Unit">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 7.

7.REPLACE MODULE.

1) Replace the body integrated unit.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0422 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 8.

System is normal.

8.CHECK MODULE.

1) Reinstall the body integrated unit.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0422 a current malfunction?

Replace the body integrated unit. Body Integrated Unit">

System is normal.

9.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Using the Subaru Select Monitor, read DTC of CAN system. Read Diagnostic Trouble Code (DTC)">

Is U0422 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULE">Go to Step 10.

10.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0420 invalid data received from power steering control module

Dtc u0423 invalid data received from instrument panel cluster control module

Other materials:

Dtc c1412 selected parameter
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C1412 SELECTED PARAMETERDTC DETECTING CONDITION:VDCCM parameter selection errorTROUBLE SYMPTOM:• ABS does not operate.• EBD does not operate.• VDC does not operate.• H ...

Dtc u0100 lost communication with ecm/pcm a
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”Detected when CAN data from the engine control module (ECM) does not arrive.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Proc ...

Operation
AUTO HEADLIGHT BEAM LEVELER SYSTEM (DIAGNOSTICS) > Read Current DataOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. On «Select System» ...