Subaru Crosstrek Service Manual: Dtc u0164 lost communication with hvac control module

DTC DETECTING CONDITION:

No data is received from A/C control panel.

TROUBLE SYMPTOM:

Cooperation control of air conditioner does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0164 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0164 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the air conditioner data no-receive detected in several modules?

Replace the A/C control panel. Control Panel">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 6.

6.REPLACE MODULE.

1) Replace the A/C control panel.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0164 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Restore the A/C control panel.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0164 a current malfunction?

Replace the A/C control panel. Control Panel">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0164 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0164 LOST COMMUNICATION WITH HVAC CONTROL MODULE">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0155 lost communication with instrument panel cluster (ipc) control module

Dtc u0327 software incompatibility with vehicle security control module

Other materials:

Installation
EXTERIOR/INTERIOR TRIM > Front GrilleINSTALLATIONCAUTION:• Install so that the front end of the under cover (b) comes inside the bumper face - front (a), and the front end of the mud guard (c) comes outside the bumper face - front (a).• Before installing the bumper face, match the cla ...

Removal
CONTROL SYSTEMS > Select CableREMOVAL1. Shift the select lever to “N” range.2. Disconnect the ground cable from battery. NOTE">NOTE:For model with battery sensor, disconnect the ground terminal from battery sensor.3. Lift up the vehicle.4. Remove the center exhaust pipe. Cen ...

Dtc b14e3 air mix door actuator stepping motor circuit open (passenger)
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B14E3 AIR MIX DOOR ACTUATOR STEPPING MOTOR CIRCUIT OPEN (PASSENGER)DTC detecting condition:Air mix door actuator stepping motor circuit is open.Trouble symptom:Temperature cannot be adjusted.Wiring d ...