Subaru Crosstrek Service Manual: Dtc u0151 lost communication with restraints control module

DTC DETECTING CONDITION:

No data is received from airbag CM.

TROUBLE SYMPTOM:

Cooperation control with airbag CM does not operate properly.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0151 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0151 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the airbag data no-receive detected in several modules?

Replace the airbag CM. Airbag Control Module">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 6.

6.REPLACE MODULE.

1) Replace the airbag CM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0151 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Reinstall the airbag CM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0151 a current malfunction?

Replace the airbag CM. Airbag Control Module">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0151 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULE">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u0140 lost communication with body control module

Dtc u0156 lost communication with information center "a"

Other materials:

Driving history registration
The items in the driving history can be registered. To change the items, operate the "  " or " " switch, and then push the button. 1. Turn the ignition switch to the "ON" position. 2. Push and hold the   button to show the selection screen. 3. After the selection scr ...

Basic diagnostic procedure Procedure
LAN SYSTEM (DIAGNOSTICS) > Basic Diagnostic ProcedurePROCEDURECAUTION:• Subaru Select Monitor is required for reading DTC, performing diagnosis, reading current data, customizing and active test (compulsory drive).• Remove foreign matter (dust, water, oil, etc.) from each control modu ...

Inspection
WIPER AND WASHER SYSTEMS > Front Washer Nozzle and HoseINSPECTION• Make sure the nozzle - windshield washer and the hose - windshield washer are not clogged.• Make sure the hose - windshield washer is not bent.• Check the position of the nozzle - windshield washer. Front Washer ...