Subaru Crosstrek Service Manual: Dtc u0101 lost communication with tcm

DTC detecting condition:

No data is received from TCM.

Trouble symptom:

Cooperation control with transmission is not performed.

1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.

Was the basic diagnostic procedure performed up to STEP 3?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 2.

Perform the basic diagnostic procedure. Basic Diagnostic Procedure">

2.CHECK DTC.

Check the displayed DTC.

Are DTCs other than U*** displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 3.

3.CHECK DTC.

Check the displayed DTC.

Is U0101 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 8.

4.CHECK DTC.

1) Check CAN communication circuit. CAN Communication Circuit Check">

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0101 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 8.

5.CHECK DTC.

Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">

Is the transmission data no-receive detected in several modules?

Replace the TCM. Transmission Control Module (TCM)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 6.

6.REPLACE MODULE.

1) Replace the TCM.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0101 a current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 7.

System is normal.

7.CHECK MODULE.

1) Reinstall the TCM.

2) Replace the module that the DTC has been detected.

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0101 a current malfunction?

Replace the TCM. Transmission Control Module (TCM)">

System is normal.

8.CHECK HARNESS.

1) Shake the harness, and check for poor contact.

2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is U0101 a current malfunction?

Repair the poor contact of harness, or replace the harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0101 LOST COMMUNICATION WITH TCM">Go to Step 9.

9.CHECK CONNECTOR.

Check the connector used for high speed CAN for poor contact.

Is there poor contact of connector?

Repair the connector that has poor contact, or replace harness.

It is possible that temporary poor communication occurs. Delete the DTC.

Dtc u1433 invalid data received from eyesight

Dtc u1232 lost communication with rear/side radar control module

Other materials:

Ignition switch light (if equipped)
For easy access to the ignition switch in the dark, the ignition switch light illuminates when the driver's door is opened or when the driver's door is unlocked using the remote keyless entry transmitter. The light remains illuminated for several tens of seconds and then gradually turns off ...

Assembly
COOLING(H4DO) > Radiator Sub Fan and Fan MotorASSEMBLYAssemble in the reverse order of disassembly.Tightening torque:4.41 N·m (0.45 kgf-m, 3.25 ft-lb)Tightening torque:3.4 N·m (0.3 kgf-m, 2.5 ft-lb) ...

Dtc p0032 a/f / o2 heater control circuit high bank 1 sensor 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0032 A/F / O2 HEATER CONTROL CIRCUIT HIGH BANK 1 SENSOR 1DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode ...