LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”
DTC DETECTING CONDITION:
No data is received from ECM.
TROUBLE SYMPTOM:
Cooperation control of transmission may not operate properly.
STEP | CHECK | YES | NO |
1.CHECK PERFORMING OF BASIC DIAGNOSTIC PROCEDURE.
Was the basic diagnostic procedure performed up to STEP 3?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 2.
Perform the basic diagnostic procedure. Basic Diagnostic Procedure">
2.CHECK DTC.
Check the displayed DTC.
Are DTCs other than U*** displayed?
Perform the diagnosis according to DTC.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 3.
3.CHECK DTC.
Check the displayed DTC.
Is U0100 a current malfunction?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 4.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 8.
4.CHECK DTC.
1) Check CAN communication circuit. CAN Communication Circuit Check">
2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is U0100 a current malfunction?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 5.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 8.
5.CHECK DTC.
Using the Subaru Select Monitor, read DTC of all the systems. Read Diagnostic Trouble Code (DTC)">
Is the engine data no-receive detected in several modules?
Replace the ECM. Engine Control Module (ECM)">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 6.
6.REPLACE MODULE.
1) Replace the ECM.
2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is U0100 a current malfunction?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 7.
System is normal.
7.CHECK MODULE.
1) Reinstall the ECM.
2) Replace the module that the DTC has been detected.
3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is U0100 a current malfunction?
Replace the ECM. Engine Control Module (ECM)">
System is normal.
8.CHECK HARNESS.
1) Shake the harness, and check for poor contact.
2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is U0100 a current malfunction?
Repair the poor contact of harness, or replace the harness.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC U0100 LOST COMMUNICATION WITH ECM/PCM “A”">Go to Step 9.
9.CHECK CONNECTOR.
Check the connector used for high speed CAN for poor contact.
Is there poor contact of connector?
Repair the connector that has poor contact, or replace harness.
It is possible that temporary poor communication occurs. Delete the DTC.
Head restraint adjustment
Both the rear window side seats and the
rear center seat are equipped with head
restraints.
WARNING
Never drive the vehicle with the
head restraints removed because
they are designed to reduce the
risk of serious neck injury in the
event that the vehicle is struck
from the rear. The ...
Disassembly
POWER ASSISTED SYSTEM (POWER STEERING) > Electric Power Steering GearboxDISASSEMBLYCAUTION:• Nut for fixing the rack is on the driver’s side only. When removing the tie-rod on the passenger’s side, turn over the boot - steering gearbox on the driver’s side, and fix the rac ...
Activating and deactivating the alarm system
To change the setting of your vehicle's
alarm system for activation or deactivation,
do the following.
1. Disarm the alarm system. Refer to
"Disarming the system" 2-30.
2. Sit in the driver's seat and shut all
doors and the rear gate.
3. Turn the ignition switch to the "ON"
position.
...