Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p2746 intermediate shaft speed sensor "b" circuit range/performance

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2746 INTERMEDIATE SHAFT SPEED SENSOR "B" CIRCUIT RANGE/PERFORMANCE

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Standing start problems

Shock occurs when engaging the lockup clutch.

Shock occurs when selecting shift position.

STEPCHECKYESNO

1.CHECK DTC.

Read the DTC using Subaru Select Monitor.

Besides DTC P2746, is DTC P2747 or P2751 displayed?

Perform the diagnosis according to DTCs other than P2746.

Perform the diagnosis according to DTC P2747. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2747 INTERMEDIATE SHAFT SPEED SENSOR "B" CIRCUIT NO SIGNAL">

1. OUTLINE OF DIAGNOSIS

Diagnosis 1

Detect the malfunction of primary speed sensor signal characteristics.

Judge as NG if the primary speed, compared with the speeds of other parts, is outside the possible range considering the hardware capabilities.

Diagnosis 2

Detect the malfunction of primary speed sensor signal characteristics.

Judge as NG if the primary speed exceeds the predetermined value.

2. EXECUTION CONDITION

Secondary Parameters

Execution condition

Diagnosis 1

12 V battery system voltage

≥ 9 V

Transmission range

Drive or Reverse

(Measured turbine shaft speed / Measured secondary pulley shaft speed)

≥ 0.4

and

≤ 2.55

Diagnosis 2

12 V battery system voltage

≥ 9 V

Transmission range

Drive or Reverse

(Measured turbine shaft speed / Measured secondary pulley shaft speed)

≥ 0.4

and

≤ 2.55

3. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

Diagnosis 1

(Measured primary pulley shaft speed / Measured secondary pulley shaft speed)

< 0.36

or

> 2.80

Diagnosis 2

Measured primary pulley shaft speed

> 7140 rpm

Time Needed for Diagnosis: 5 seconds

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p160a random access memory (ram) error
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P160A RANDOM ACCESS MEMORY (RAM) ERRORDTC DETECTING CONDITION:Detected when two consecu ...

Dtc p2747 intermediate shaft speed sensor "b" circuit no signal
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2747 INTERMEDIATE SHAFT SPEED SENSOR "B" CIRCUIT NO SIGNALDTC detecting cond ...

Other materials:

Installation
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transmission Mounting SystemINSTALLATION1. PITCHING STOPPER1. Install the pitching stopper.Tightening torque:T1: 50 N·m (5.1 kgf-m, 36.9 ft-lb)T2: 58 N·m (5.9 kgf-m, 42.8 ft-lb)2. Install the air intake boot. Air Intake Boot > INSTALLA ...

Installation
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Fuel FilterINSTALLATION1. Install O-ring (A), O-ring (B), and backup ring (C) to the pressure regulator.NOTE:• Use new O-rings.• Apply gasoline to the O-ring and backup ring.2. Install the pressure regulator to the fuel filter assembly.3. Install ...

Caution
LIGHTING SYSTEM > General DescriptionCAUTION• Before disassembling or reassembling parts, always disconnect the battery ground cable from battery. When replacing the audio, control module and other parts provided with memory functions, record the memory contents before disconnecting the bat ...

© 2016-2025 Copyright www.sucross.com