Subaru Crosstrek Service Manual: Dtc p2404 evap system leak detection pump sense circuit range/performance

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

1.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check the appropriate DTC using the “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 2.

2.CHECK LEAK CHECK VALVE ASSEMBLY PUMP.

Using the Subaru Select Monitor, operate the leak check valve assembly pump.

NOTE:

For detailed operation procedures, refer to the “Active Test”. Active Test">

Does the leak check valve assembly pump operate?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 3.

3.CHECK POWER SUPPLY OF LEAK CHECK VALVE ASSEMBLY.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from the leak check valve assembly.

3) Turn the ignition switch to ON.

4) Measure the voltage between the leak check valve assembly connector and chassis ground.

Connector & terminal

(R400) No. 3 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 4.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit in harness between the main relay and the leak check valve assembly connector

• Poor contact of main relay connector

• Poor contact of coupling connector

4.CHECK HARNESS BETWEEN ECM AND LEAK CHECK VALVE ASSEMBLY CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Measure the resistance of harness between ECM connector and the leak check valve assembly connector.

Connector & terminal

(B135) No. 18 — (R400) No. 4:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 5.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit in harness between ECM connector and the leak check valve assembly connector

• Poor contact of coupling connector

5.CHECK HARNESS BETWEEN ECM AND LEAK CHECK VALVE ASSEMBLY CONNECTOR.

1) Measure the resistance of harness between ECM connector and chassis ground.

Connector & terminal

(B135) No. 18 — Chassis ground:

Is the resistance 1 M? or more?

Replace the leak check valve assembly. Leak Check Valve Assembly">

Repair the short circuit to ground in harness between ECM connector and leak check valve assembly connector.

6.CHECK LEAK CHECK VALVE ASSEMBLY SWITCHING VALVE.

Using the Subaru Select Monitor, operate the leak check valve assembly switching valve.

NOTE:

For detailed operation procedures, refer to the “Active Test”. Active Test">

Does the leak check valve assembly switching valve operate?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 10.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 7.

7.CHECK POWER SUPPLY OF LEAK CHECK VALVE ASSEMBLY.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from the leak check valve assembly.

3) Turn the ignition switch to ON.

4) Measure the voltage between the leak check valve assembly connector and chassis ground.

Connector & terminal

(R400) No. 5 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 8.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit in harness between the main relay and the leak check valve assembly connector

• Poor contact of main relay connector

• Poor contact of coupling connector

8.CHECK HARNESS BETWEEN ECM AND LEAK CHECK VALVE ASSEMBLY CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Measure the resistance of harness between ECM connector and the leak check valve assembly connector.

Connector & terminal

(B135) No. 1 — (R400) No. 1:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2404 EVAP SYSTEM LEAK DETECTION PUMP SENSE CIRCUIT RANGE/PERFORMANCE">Go to Step 9.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit in harness between ECM connector and the leak check valve assembly connector

• Poor contact of coupling connector

9.CHECK HARNESS BETWEEN ECM AND LEAK CHECK VALVE ASSEMBLY CONNECTOR.

1) Measure the resistance of harness between ECM connector and chassis ground.

Connector & terminal

(B135) No. 1 — Chassis ground:

Is the resistance 1 M? or more?

Replace the leak check valve assembly. Leak Check Valve Assembly">

Repair the short circuit to ground in harness between ECM connector and leak check valve assembly connector.

10.CHECK EVAPORATIVE EMISSION CONTROL SYSTEM.

Perform drive cycle I. Drive Cycle > PROCEDURE">

Is DTC P2404 displayed on the display?

Replace the leak check valve assembly. Leak Check Valve Assembly">

Even if DTC is detected, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

For the detection standard, refer to DTC P0455. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0455 EVAP SYSTEM (CPC) LEAK DETECTED (LARGE LEAK)">

Dtc p2402 evap system leak detection pump control circuit high

Dtc p2419 evap system switching valve control circuit low

Other materials:

Inspection
AIRBAG SYSTEM > Roll ConnectorINSPECTION1. VISUAL INSPECTIONCheck for the following, and replace the damaged parts with new parts.• Combination switch is cracked or deformed.• Roll connector is cracked or deformed.2. UNIT INSPECTION OF ROLL CONNECTORCAUTION:• Do not rotate the r ...

Inspection
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Subaru Select MonitorINSPECTION1. COMMUNICATION FOR INITIALIZING IMPOSSIBLEDetecting condition:Defective harness connectorTrouble symptom:Communication is impossible between the TPMS & keyless entry CM or TPMS CM and the Subaru Select Monitor.WI ...

Dtc p0171 system too lean bank 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0171 SYSTEM TOO LEAN BANK 1Refer to DTC P0172 for diagnostic procedure. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">1. OUTLINE OF DIAGNOSISDetect fu ...