Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p2135 throttle/pedal position sensor/switch "a"/"b" voltage correlation

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p2135 throttle/pedal position sensor/switch "a"/"b" voltage correlation

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2135 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A"/"B" VOLTAGE CORRELATION

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Improper idling

Poor driving performance

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

Wiring diagram:

Engine electrical system Engine Electrical System">

STEPCHECKYESNO

1.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Disconnect the connectors from electronic throttle control.

4) Measure the resistance between ECM connector and chassis ground.

Connector & terminal

(B134) No. 19 — Chassis ground:

(B134) No. 18 — Chassis ground:

(B134) No. 18 — (B136) No. 4:

(B134) No. 28 — Chassis ground:

(B134) No. 28 — (B136) No. 4:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2135 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A"/"B" VOLTAGE CORRELATION">Go to Step 2.

Repair the ground short circuit of harness between ECM connector and electronic throttle control connector.

2.CHECK SHORT CIRCUIT INSIDE THE ECM.

1) Connect the connector to ECM.

2) Measure the resistance between electronic throttle control connector and engine ground.

Connector & terminal

(E57) No. 6 — Engine ground:

(E57) No. 4 — Engine ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2135 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A"/"B" VOLTAGE CORRELATION">Go to Step 3.

Repair the ground short circuit of harness between ECM connector and electronic throttle control connector. Replace the ECM if defective. Engine Control Module (ECM)">

3.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Disconnect the connector from ECM.

2) Measure the resistance of harness between ECM connector and electronic throttle control connector.

Connector & terminal

(B134) No. 18 — (E57) No. 6:

(B134) No. 28 — (E57) No. 4:

(B134) No. 29 — (E57) No. 3:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2135 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A"/"B" VOLTAGE CORRELATION">Go to Step 4.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

Open circuit in harness between ECM connector and electronic throttle control connector

Poor contact of coupling connector

4.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Connect the connector to ECM.

2) Measure the resistance between electronic throttle control connector and engine ground.

Connector & terminal

(E57) No. 3 — Engine ground:

Is the resistance less than 5 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2135 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A"/"B" VOLTAGE CORRELATION">Go to Step 5.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

Open circuit of harness between ECM connector and engine ground

Poor contact of ECM connector

Poor contact of coupling connector

5.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Turn the ignition switch to ON.

2) Measure the voltage between electronic throttle control connector and engine ground.

Connector & terminal

(E57) No. 6 (+) — Engine ground (−):

(E57) No. 4 (+) — Engine ground (−):

Is the voltage 5 V or more?

Repair the short circuit to power in the harness between ECM connector and electronic throttle control connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2135 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A"/"B" VOLTAGE CORRELATION">Go to Step 6.

6.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Measure the resistance between ECM connectors.

Connector & terminal

(B134) No. 19 — (B134) No. 18:

(B134) No. 19 — (B134) No. 28:

Is the resistance 1 M? or more?

Repair the poor contact of electronic throttle control connector. Replace the electronic throttle control if defective. Throttle Body">

Repair the short circuit to power in the harness between ECM connector and electronic throttle control connector.

1. OUTLINE OF DIAGNOSIS

Judge as NG when the signal level of throttle position sensor 1 is different from the throttle position sensor 2.

2. COMPONENT DESCRIPTION

(1)

Throttle position sensor 1 signal

(3)

Throttle position sensor

(4)

Engine control module (ECM)

(2)

Throttle position sensor 2 signal

3. EXECUTION CONDITION

Secondary Parameters

Execution condition

Ignition switch

ON

Battery voltage

≥ 6 V

4. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

Signal difference between two sensors

Within NG range of Details of Judgment value

Details of Judgment Value

(X1)

2.125 °

(X2)

4.25 °

(X3)

9 °

(X4)

31.625 °

(Y1)

4.736 °

(Y2)

5.736 °

(Y3)

7.861 °

(Y4)

9.986 °

(Y5)

11.986 °

Time Needed for Diagnosis: 212 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p2128 throttle/pedal position sensor/switch "e" circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2128 THROTTLE/PEDAL POSITION SENSOR/SWITCH "E" CIRCUIT HIGHDTC detecting condition:Immediately at ...

Dtc p2138 throttle/pedal position sensor/switch "d"/"e" voltage correlation
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2138 THROTTLE/PEDAL POSITION SENSOR/SWITCH "D"/"E" VOLTAGE CORRELATIONDTC DETECTING COND ...

Other materials:

Diagnostic procedure for subaru select monitor communication Communication for initializing impossible
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure for Subaru Select Monitor CommunicationCOMMUNICATION FOR INITIALIZING IMPOSSIBLEDIAGNOSIS:Open or short circuit in data link connectorTROUBLE SYMPTOM:Subaru Select Monitor communication failureWIRING DIAGRAM:Engine electrical system Engine Electr ...

Preparation tool
DIFFERENTIALS > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS398477701HANDLE• Used for installing the rear bearing race.• Used for installing the front bearing race.398477702DRIFT• Used for installing the front bearing race. (T-type) ...

Dtc u0416 invalid data received from vehicle dynamics control module
LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0416 INVALID DATA RECEIVED FROM VEHICLE DYNAMICS CONTROL MODULEDTC DETECTING CONDITION:Data from VDCCM is faulty.TROUBLE SYMPTOM:ABS warning light and VDC warning light illuminate.STEPCHECKYESNO1.CHECK PERFORMI ...

© 2016-2024 Copyright www.sucross.com