Subaru Crosstrek Service Manual: Dtc p2123 throttle/pedal position sensor/switch "d" circuit high

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p2123 throttle/pedal position sensor/switch "d" circuit high

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2123 THROTTLE/PEDAL POSITION SENSOR/SWITCH "D" CIRCUIT HIGH

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

• Improper idling

• Poor driving performance

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

Wiring diagram:

Engine electrical system Engine Electrical System">

STEP	CHECK	YES	NO

1.CHECK HARNESS BETWEEN ECM AND ACCELERATOR PEDAL POSITION SENSOR CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Disconnect the connector from the accelerator pedal position sensor.

4) Measure the resistance of harness between ECM connector and accelerator pedal position sensor connector.

Connector & terminal

(B135) No. 23 — (B315) No. 6:

(B135) No. 29 — (B315) No. 5:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2123 THROTTLE/PEDAL POSITION SENSOR/SWITCH "D" CIRCUIT HIGH">Go to Step 2.

Repair the open circuit of harness between ECM connector and accelerator pedal position sensor connector.

2.CHECK HARNESS BETWEEN ECM AND ACCELERATOR PEDAL POSITION SENSOR CONNECTOR.

1) Connect the connector to ECM.

2) Measure the resistance between accelerator pedal position sensor connector and chassis ground.

Connector & terminal

(B315) No. 5 — Chassis ground:

Is the resistance less than 5 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2123 THROTTLE/PEDAL POSITION SENSOR/SWITCH "D" CIRCUIT HIGH">Go to Step 3.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit of harness between ECM connector and engine ground

• Poor contact of ECM connector

• Poor contact of coupling connector

3.CHECK HARNESS BETWEEN ECM AND ACCELERATOR PEDAL POSITION SENSOR CONNECTOR.

1) Turn the ignition switch to ON.

2) Measure the voltage between accelerator pedal position sensor connector and chassis ground.

Connector & terminal

(B315) No. 6 (+) — Chassis ground (−):

Is the voltage 5 V or more?

Repair the short circuit to power supply in harness between ECM connector and accelerator pedal position sensor connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2123 THROTTLE/PEDAL POSITION SENSOR/SWITCH "D" CIRCUIT HIGH">Go to Step 4.

4.CHECK HARNESS BETWEEN ECM AND ACCELERATOR PEDAL POSITION SENSOR CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Measure the resistance between ECM connectors.

Connector & terminal

(B135) No. 21 — (B135) No. 23:

Is the resistance 1 M? or more?

Repair the poor contact of accelerator pedal position sensor connector. Replace the accelerator pedal if defective. Accelerator Pedal">

Repair the short circuit to power supply in harness between ECM connector and accelerator pedal position sensor connector.

1. OUTLINE OF DIAGNOSIS

Detect the open or short circuit of accelerator pedal position sensor 1.

Judge as NG if out of specification.

2. COMPONENT DESCRIPTION

(1)	Engine control module (ECM)	(3)	Accelerator pedal position sensor 2 signal	(4)	Accelerator pedal position sensor
(2)	Accelerator pedal position sensor 1 signal

3. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	≥ 6 V

4. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Sensor 1 input voltage	≥ 4.737 V

Time Needed for Diagnosis: 32 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p2122 throttle/pedal position sensor/switch "d" circuit low

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2122 THROTTLE/PEDAL POSITION SENSOR/SWITCH "D" CIRCUIT LOWDTC detecting condition:Immediately at f ...

Dtc p2127 throttle/pedal position sensor/switch "e" circuit low

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2127 THROTTLE/PEDAL POSITION SENSOR/SWITCH "E" CIRCUIT LOWDTC detecting condition:Immediately at f ...

Other materials:

Removal
LIGHTING SYSTEM > Front Fog Light AssemblyREMOVAL1. Disconnect the ground cable from battery. NOTE">2. Lift up the vehicle.3. Remove the screw and clips, and turn over the front side of the mud guard - front.4. From the bottom of the bumper face - front, remove the fog light assembly - f ...

Rear window wiper blade assembly
1. Raise the wiper arm off the rear window. 2. Turn the wiper blade assembly counterclockwise. 3. Pull the wiper blade assembly toward you to remove it from the wiper arm. 4. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 5. Hold the wiper arm ...

Dtc b16f3 front sub sensor lh recognition error
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B16F3 FRONT SUB SENSOR LH RECOGNITION ERRORDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:Front sub sensor (LH) is misinstalled.CAUTION:Before performing diagnosis, refer to “CAUTION&rdqu ...