Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p2103 throttle actuator "a" control motor circuit high

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2103 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT HIGH

DTC DETECTING CONDITION:

Immediately at fault recognition

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

WIRING DIAGRAM:

Engine electrical system Engine Electrical System">

STEPCHECKYESNO

1.CHECK ELECTRONIC THROTTLE CONTROL RELAY.

1) Turn the ignition switch to OFF.

2) Remove the electronic throttle control relay.

3) Measure the resistance between electronic throttle control relay terminals.

Terminals

No. 14 — No. 15:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2103 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT HIGH">Go to Step 2.

Replace the electronic throttle control relay. Electronic Throttle Control Relay">

2.CHECK SHORT CIRCUIT OF ELECTRONIC THROTTLE CONTROL RELAY POWER SUPPLY.

1) Turn the ignition switch to ON.

2) Measure the voltage between electronic throttle control relay connector and chassis ground.

Connector & terminal

(B225) No. 14 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Repair the short circuit to power in the harness between ECM connector and electronic throttle control relay connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2103 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT HIGH">Go to Step 3.

3.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL RELAY CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Measure the resistance between ECM connector and chassis ground.

Connector & terminal

(B135) No. 17 — Chassis ground:

Is the resistance 1 M? or more?

Repair the poor contact of ECM connector.

Repair the short circuit to ground in harness between ECM connector and electronic throttle control relay connector.

1. OUTLINE OF DIAGNOSIS

Judge as NG when the electronic throttle control power is supplied even when ECM sets the electronic throttle control relay to OFF.

2. COMPONENT DESCRIPTION

(1)

Engine control module (ECM)

(3)

Drive circuit

(5)

Motor

(2)

Voltage detection circuit

(4)

Electronic throttle control relay

3. EXECUTION CONDITION

Secondary Parameters

Execution condition

Battery voltage

≥ 6 V

Electronic throttle control relay output

OFF

4. GENERAL DRIVING CYCLE

When ignition switch ON > OFF

Ignition switch OFF > ON (Only after clearing memory)

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

Motor power voltage

≥ 5 V

Time Needed for Diagnosis: 600 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p2102 throttle actuator "a" control motor circuit low
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2102 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT LOWDTC DETECTING CONDITION:Immediately at fault r ...

Dtc p2109 throttle/pedal position sensor "a" minimum stop performance
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2109 THROTTLE/PEDAL POSITION SENSOR "A" MINIMUM STOP PERFORMANCENOTE:For the diagnostic procedure, ...

Other materials:

Before checking or servicing in the engine  compartment
WARNING Always stop the engine and apply the parking brake firmly to prevent the vehicle from moving. Always let the engine cool down. Engine parts become very hot when the engine is running and remain hot for some time after the engine has stopped. Do not spill engine oil, engine coolan ...

Dtc p0977 shift solenoid "b" control circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0977 SHIFT SOLENOID "B" CONTROL CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionTrouble symptom:Gear is not changed. (No down-shift)CAUTION:Use the check bo ...

Caution
DRIVE SHAFT SYSTEM > General DescriptionCAUTION• When performing any work, always wear work clothes, a work cap and protective shoes. Additionally, wear a helmet, protective goggles, etc. if necessary.• Remove contamination including dirt and corrosion before removal, installation, di ...

© 2016-2024 Copyright www.sucross.com