Subaru Crosstrek Service Manual: Dtc p2102 throttle actuator "a" control motor circuit low

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p2102 throttle actuator "a" control motor circuit low

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2102 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT LOW

DTC DETECTING CONDITION:

Immediately at fault recognition

TROUBLE SYMPTOM:

• Improper idling

• Poor driving performance

• Engine stall

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

WIRING DIAGRAM:

Engine electrical system Engine Electrical System">

STEP	CHECK	YES	NO

1.CHECK ELECTRONIC THROTTLE CONTROL RELAY.

1) Turn the ignition switch to OFF.

2) Remove the electronic throttle control relay.

3) Connect the battery to terminals No. 16 and No. 17 of electronic throttle control relay.

4) Measure the resistance between electronic throttle control relay terminals.

Terminals

No. 14 — No. 15:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2102 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT LOW">Go to Step 2.

Replace the electronic throttle control relay. Electronic Throttle Control Relay">

2.CHECK POWER SUPPLY OF ELECTRONIC THROTTLE CONTROL RELAY.

Measure the voltage between electronic throttle control relay connector and chassis ground.

Connector & terminal

(B225) No. 15 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2102 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT LOW">Go to Step 3.

Repair the open or short to ground in the power supply circuit.

3.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL RELAY CONNECTOR.

1) Disconnect the connector from ECM.

2) Turn the ignition switch to ON.

3) Measure the voltage between electronic throttle control relay connector and chassis ground.

Connector & terminal

(B225) No. 17 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Repair the short circuit to power in the harness between ECM connector and electronic throttle control relay connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2102 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT LOW">Go to Step 4.

4.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL RELAY CONNECTOR.

1) Turn the ignition switch to OFF.

2) Measure the resistance between electronic throttle control relay connector and chassis ground.

Connector & terminal

(B225) No. 14 — Chassis ground:

(B225) No. 17 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2102 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT LOW">Go to Step 5.

Repair the short circuit to ground in harness between ECM connector and electronic throttle control relay connector.

5.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL RELAY CONNECTOR.

Measure the resistance between ECM connector and electronic throttle control relay connector.

Connector & terminal

(B135) No. 17 — (B225) No. 17:

(B135) No. 7 — (B225) No. 14:

Is the resistance less than 1 ??

Repair the poor contact of ECM connector.

Repair the open circuit in harness between ECM connector and electronic throttle control relay connector.

1. OUTLINE OF DIAGNOSIS

Judge as NG when the electronic throttle control power is not supplied even when ECM sets the electric control throttle relay to ON.

2. COMPONENT DESCRIPTION

(1)	Engine control module (ECM)	(3)	Drive circuit	(5)	Motor
(2)	Voltage detection circuit	(4)	Electronic throttle control relay

3. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	≥ 11 V
Electronic throttle control relay output	ON

4. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Motor power voltage	≤ 5 V

Time Needed for Diagnosis: 352 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p2101 throttle actuator "a" control motor circuit range/performance

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2101 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT RANGE/PERFORMANCEDTC detecting condition:Immediat ...

Dtc p2103 throttle actuator "a" control motor circuit high

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2103 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT HIGHDTC DETECTING CONDITION:Immediately at fault ...

Other materials:

Installation
POWER ASSISTED SYSTEM (POWER STEERING) > Electric Power Steering GearboxINSTALLATION1. Insert the steering gearbox assembly into crossmember, being careful not to damage the boot of the steering gearbox assembly.2. Install the steering gearbox assembly to the crossmember by tightening the bolts t ...

Disassembly
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Drive Pinion Shaft AssemblyDISASSEMBLYNOTE:Attach a cloth to the end of driven shaft (on the frictional side of the thrust needle bearing) to prevent damage during disassembly or reassembly.1. Flatten the tab of the lock nut. Remove the lock nut with ST ...

Engine oil consumption
Some engine oil will be consumed while driving. The rate of consumption can be affected by such factors as transmission type, driving style, terrain and temperature. Under the following conditions, oil consumption can be increased and thus require refilling between maintenance intervals: ...