Subaru Crosstrek Service Manual: Dtc p2012 tgv control circuit low bank 2

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p2012 tgv control circuit low bank 2

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2012 TGV CONTROL CIRCUIT LOW BANK 2

DTC DETECTING CONDITION:

Immediately at fault recognition

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

WIRING DIAGRAM:

Engine electrical system Engine Electrical System">

STEP	CHECK	YES	NO

1.CHECK HARNESS BETWEEN ECM AND TUMBLE GENERATOR VALVE ACTUATOR LH CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Measure the voltage between ECM connector and chassis ground.

Connector & terminal

(B134) No. 23 (+) — Chassis ground (−):

(B134) No. 24 (+) — Chassis ground (−):

Is the voltage 5 V or more?

Repair the short circuit to power in harness between ECM connector and tumble generator valve actuator LH connector.

Replace the tumble generator valve actuator LH. Tumble Generator Valve Actuator">

1. OUTLINE OF DIAGNOSIS

Detect the open or short circuit of tumble generator valve motor.

Judge as NG when the overcurrent signal is sent from IC after tumble generator valve driving IC diagnosis.

2. COMPONENT DESCRIPTION

(1)

Engine control module (ECM)

(2)

Tumble generator valve

(3)

Battery

3. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	≥ 10.9 V
TGV command	= Open or = closed

Secondary Parameters

Execution condition

Battery voltage

≥ 10.9 V

TGV command

= Open

= closed

4. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Overcurrent signal from driver IC Short circuit to GND is detected when IC current > 16 A or Short circuit to B+ is detected when IC current > 14 A	= ON

Malfunction Criteria

Threshold Value

Overcurrent signal from driver IC

Short circuit to GND is detected when IC current > 16 A

Short circuit to B+ is detected when IC current > 14 A

= ON

Time Needed for Diagnosis: 1 second

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p2009 tgv control circuit low bank 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2009 TGV CONTROL CIRCUIT LOW BANK 1DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After ser ...

Dtc p2096 post catalyst fuel trim system too lean bank 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2096 POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1DTC detecting condition:Detected when two consecutive dri ...

Other materials:

Diagnostic procedure without diagnostic trouble code (dtc) Check shift indicator
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure without Diagnostic Trouble Code (DTC)CHECK SHIFT INDICATORDiagnosis:• CAN communication is abnormal with the combination meter.• Combination meter malfunctionTrouble symptom:• Shift indicator does not displa ...

Assembly
EXTERIOR/INTERIOR TRIM > Door TrimASSEMBLY1. Bend the claws while pushing the weather strip - door INN against the door trim so that there is no gap.CAUTION:Beware of the direction of folding the claws.(a)Rivet(b)Direction of folding claws(c)Claw bending direction: bend forward for LH side, backw ...

Dtc u0422 invalid data received from body control module
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0422 INVALID DATA RECEIVED FROM BODY CONTROL MODULEReceived error data from BIU.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Procedure > PROCEDURE"> ...