Subaru Crosstrek Service Manual: Dtc p2007 tgv control stuck closed bank 2

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p2007 tgv control stuck closed bank 2

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P2007 TGV CONTROL STUCK CLOSED BANK 2

DTC DETECTING CONDITION:

Immediately at fault recognition

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

STEP	CHECK	YES	NO

1.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check the appropriate DTC using the “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2007 TGV CONTROL STUCK CLOSED BANK 2">Go to Step 2.

2.CHECK TUMBLE GENERATOR VALVE LH.

1) Remove the tumble generator valve assembly LH.

2) Check the tumble generator valve.

Is there any dirt or clogging with foreign objects in the tumble generator valve?

Clean the tumble generator valve.

Replace the tumble generator valve LH. Tumble Generator Valve Assembly">

1. OUTLINE OF DIAGNOSIS

Detect the malfunction of tumble generator valve motor function.

Judge close fixing malfunction when the opening degree is small even after finishing the tumble generator valve open driving.

2. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	≥ 10.9 V
Elapsed time of TGV commanded* to "open"	≥ 1600 ms

3. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

4. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
TGV position	= Closed
As defined by: TGV angle position sensor voltage < 2.5 V

Malfunction Criteria

Threshold Value

TGV position

= Closed

As defined by:

TGV angle position sensor voltage < 2.5 V

Time Needed for Diagnosis: 3000 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p2006 tgv control stuck closed bank 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2006 TGV CONTROL STUCK CLOSED BANK 1DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After se ...

Dtc p2009 tgv control circuit low bank 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2009 TGV CONTROL CIRCUIT LOW BANK 1DTC DETECTING CONDITION:Immediately at fault recognitionCAUTION:After ser ...

Other materials:

Dtc p0708 transmission range sensor "a" circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0708 TRANSMISSION RANGE SENSOR "A" CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionTrouble symptom:• Shift characteristics are erroneous.• The r ...

Basic diagnostic procedure Procedure
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Basic Diagnostic ProcedurePROCEDURECAUTION:Before removal or installation, be sure to remove any foreign matter (dust, moisture, oil, etc.) from the TPMS & keyless entry CM connector or TPMS CM connector.NOTE:To check harness for open or short c ...

Dtc b1406 scu_eeprom
IMMOBILIZER (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1406 SCU_EEPROMDTC DETECTING CONDITION:• Defective security control module• ROM of security control module cannot be accessedCAUTION:When the security control module is replaced, registration of th ...