Subaru Crosstrek Service Manual: Dtc p0977 shift solenoid "b" control circuit high

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Gear is not changed. (No down-shift)

CAUTION:

Use the check board when measuring the TCM terminal voltage and resistance.

1.CHECK HARNESS.

1) Turn the ignition switch to OFF.

2) Disconnect the TCM connector.

3) Disconnect the transmission connector.

4) Measure the resistance between TCM connector and transmission connectors.

Connector & terminal

(B54) No. 30 — (B11) No. 3:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0977 SHIFT SOLENOID "B" CONTROL CIRCUIT HIGH">Go to Step 2.

Repair the open circuit of harness.

2.CHECK HARNESS.

1) Turn the ignition switch to ON.

2) Measure the voltage between TCM connector and chassis ground.

Connector & terminal

(B54) No. 30 (+) — Chassis ground (−):

Is the voltage approx. 0 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0977 SHIFT SOLENOID "B" CONTROL CIRCUIT HIGH">Go to Step 3.

Repair the short circuit of harness.

3.CHECK PRIMARY DOWN SOLENOID.

Measure the resistance between transmission connector and transmission body.

Connector & terminal

(T4) No. 3 — Transmission body:

Is the resistance approx. 10 — 13.5 ?? (when cold)

Check for poor contact of connector, and if no fault is found, replace the TCM. Transmission Control Module (TCM)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0977 SHIFT SOLENOID "B" CONTROL CIRCUIT HIGH">Go to Step 4.

4.CHECK HARNESS INSIDE TRANSMISSION.

CAUTION:

Start work after ATF cools down.

1) Remove the transmission valve cover.

2) Check for the harness pinch, damage.

Is there any fault in the harness?

Replace the transmission harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0977 SHIFT SOLENOID "B" CONTROL CIRCUIT HIGH">Go to Step 5.

5.CHECK HARNESS INSIDE TRANSMISSION.

1) Disconnect the control valve body connector.

2) Turn the ignition switch to ON.

3) Measure the voltage between transmission connector and transmission body.

Connector & terminal

(T4) No. 3 (+) — Transmission body (−):

Is the voltage approx. 0 V?

Replace the control valve body. Control Valve Body">

Replace the transmission harness.

• Detect short circuit to power supply or open circuit of the shift-down fluid pressure control solenoid drive circuit.

• Judge as NG when an abnormal signal is received from the solenoid driver IC of the shift-down fluid pressure control solenoid drive circuit.

Dtc p0976 shift solenoid "b" control circuit low

Dtc p160a random access memory (ram) error

Other materials:

Removal
FRONT SUSPENSION > Front Ball JointREMOVAL1. Lift up the vehicle, and then remove the front wheels.2. Remove the under cover - front. Front Under Cover > REMOVAL">3. Remove the clamp - stabilizer bushing on the left and right sides.4. Remove the ball joint assembly.(1) Pull out the co ...

Removal
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transfer Drive GearREMOVAL1. Remove the manual transmission assembly from the vehicle. Manual Transmission Assembly > REMOVAL">2. Remove the back-up light switch and the neutral position switch. Switches and Harness > REMOVAL">3. ...

Temperature control
Type A Turn the temperature control dial over a range from the blue side (cool) to red side (warm) to regulate the temperature of airflow from the air outlets. Type B, C and D Turn the temperature control dial to set the preferred interior temperature. With the dial set to your preferred tem ...