Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p0976 shift solenoid "b" control circuit low

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0976 SHIFT SOLENOID "B" CONTROL CIRCUIT LOW

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Gear is not changed. (No down-shift)

CAUTION:

Use the check board when measuring the TCM terminal voltage and resistance.

Wiring diagram:

CVT control system CVT Control System">

STEPCHECKYESNO

1.CHECK HARNESS.

1) Turn the ignition switch to OFF.

2) Disconnect the TCM connector.

3) Disconnect the transmission connector.

4) Measure the resistance between TCM connector and chassis ground.

Connector & terminal

(B54) No. 30 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0976 SHIFT SOLENOID "B" CONTROL CIRCUIT LOW">Go to Step 2.

Repair the short circuit of harness.

2.CHECK PRIMARY DOWN SOLENOID.

Measure the resistance between transmission connector and transmission body.

Connector & terminal

(T4) No. 3 — Transmission body:

Is the resistance approx. 10 — 13.5 ?? (when cold)

Check for poor contact of connector, and if no fault is found, replace the TCM. Transmission Control Module (TCM)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0976 SHIFT SOLENOID "B" CONTROL CIRCUIT LOW">Go to Step 3.

3.CHECK HARNESS INSIDE TRANSMISSION.

CAUTION:

Start work after ATF cools down.

1) Remove the transmission valve cover.

2) Check for the harness pinch, damage.

Is there any fault in the harness?

Replace the transmission harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0976 SHIFT SOLENOID "B" CONTROL CIRCUIT LOW">Go to Step 4.

4.CHECK HARNESS INSIDE TRANSMISSION.

1) Disconnect the control valve body connector.

2) Measure the resistance between transmission connector and transmission body.

Connector & terminal

(T4) No. 3 — Transmission body:

Is the resistance 1 M? or more?

Replace the control valve body. Control Valve Body">

Replace the transmission harness.

1. OUTLINE OF DIAGNOSIS

Detect the ground short of the shift-down fluid pressure control solenoid drive circuit.

Judge as NG when an abnormal signal is received from the solenoid driver IC of the shift-down fluid pressure control solenoid drive circuit.

2. EXECUTION CONDITION

Secondary Parameters

Execution condition

12 V battery system voltage

≥ 9 V

Commanded duty of shift down pressure control solenoid

100%

3. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

Signal of malfunction from solenoid driver IC

ON

As defined by:

Measured shift down pressure control solenoid voltage ≤ 0.8 V

Time Needed for Diagnosis: 0.2 seconds

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0974 shift solenoid "a" control circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0974 SHIFT SOLENOID "A" CONTROL CIRCUIT HIGHDTC detecting condition:Immediat ...

Dtc p0977 shift solenoid "b" control circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0977 SHIFT SOLENOID "B" CONTROL CIRCUIT HIGHDTC detecting condition:Immediat ...

Other materials:

Removal
LIGHTING SYSTEM > Headlight AssemblyREMOVALCAUTION:• Do not perform work with wet hands, because there is a possibility of electrical shock.• The HID type uses very high voltages for the lighting circuit. Make sure that the power supply is turned OFF before working.1. Disconnect the g ...

Automatic headlight beam leveler warning light (models with HID headlights)
This light illuminates when the automatic headlight beam leveler does not operate normally. If this light illuminates while driving or does not turn off approximately 3 seconds after turning the ignition switch to the "ON" position, have your vehicle inspected at your SUBARU dealer. Fr ...

Dtc b2223 gerda malfunction
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2223 GERDA MALFUNCTIONDTC DETECTING CONDITION:When the system microcomputer can not send/receive the data with the image microcomputer normally.TROUBLE SYMPTOM:There is no display on the TFT. O ...

© 2016-2024 Copyright www.sucross.com