Subaru Crosstrek Service Manual: Dtc p0973 shift solenoid "a" control circuit low
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC P0973 SHIFT SOLENOID "A" CONTROL CIRCUIT LOW
DTC detecting condition:
Immediately at fault recognition
Trouble symptom:
Gear is not changed. (No up-shift)
CAUTION:
Use the check board when measuring the TCM terminal voltage and resistance.
Wiring diagram:
CVT control system CVT Control System">
| STEP | CHECK | YES | NO |
1.CHECK HARNESS.
1) Turn the ignition switch to OFF.
2) Disconnect the TCM connector.
3) Disconnect the transmission connector.
4) Measure the resistance between TCM connector and chassis ground.
Connector & terminal
(B54) No. 47 — Chassis ground:
Is the resistance 1 M? or more?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0973 SHIFT SOLENOID "A" CONTROL CIRCUIT LOW">Go to Step 2.
Repair the short circuit of harness.
2.CHECK PRIMARY UP SOLENOID.
Measure the resistance between transmission connector and transmission body.
Connector & terminal
(T4) No. 2 — Transmission body:
Is the resistance approx. 10 — 13.5 ?? (when cold)
Check for poor contact of connector, and if no fault is found, replace the TCM. Transmission Control Module (TCM)">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0973 SHIFT SOLENOID "A" CONTROL CIRCUIT LOW">Go to Step 3.
3.CHECK HARNESS INSIDE TRANSMISSION.
CAUTION:
Start work after ATF cools down.
1) Remove the transmission valve cover.
2) Check for the harness pinch, damage.
Is there any fault in the harness?
Replace the transmission harness.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0973 SHIFT SOLENOID "A" CONTROL CIRCUIT LOW">Go to Step 4.
4.CHECK HARNESS INSIDE TRANSMISSION.
1) Disconnect the control valve body connector.
2) Measure the resistance between transmission connector and transmission body.
Connector & terminal
(T4) No. 2 — Transmission body:
Is the resistance 1 M? or more?
Replace the control valve body. Control Valve Body">
Replace the transmission harness.
1. OUTLINE OF DIAGNOSIS
• Detect the ground short of the shift-up fluid pressure control solenoid drive circuit.
• Judge as NG when an abnormal signal is received from the solenoid driver IC of the shift-up fluid pressure control solenoid drive circuit.
2. EXECUTION CONDITION
Secondary Parameters | Execution condition |
12 V battery system voltage | ≥ 9 V |
Commanded duty of shift up pressure control solenoid | 100% |
3. DIAGNOSTIC METHOD
If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.
Malfunction Criteria | Threshold Value |
Signal of malfunction from solenoid driver IC | ON |
As defined by: | |
Measured shift up pressure control solenoid voltage ≤ 0.8 V |
Time Needed for Diagnosis: 0.2 seconds
Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.
Dtc p0971 pressure control solenoid "c" control circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0971 PRESSURE CONTROL SOLENOID "C" CONTROL CIRCUIT HIGHDTC detecting conditi ...
Dtc p0974 shift solenoid "a" control circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0974 SHIFT SOLENOID "A" CONTROL CIRCUIT HIGHDTC detecting condition:Immediat ...
Other materials:
Dtc p1531 battery current sensor circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P1531 BATTERY CURRENT SENSOR CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION&q ...
Protector tape Installation
EXTERIOR BODY PANELS > Protector TapeINSTALLATIONApply the protector tape by the following steps.1. REAR QUARTER PROTECTOR (MODELS WITHOUT SIDE GARNISH)(1)Apply the protector tape by aligning it to the rounded edge. 1. Clean the area around applying position to remove any foreign objects on bo ...
Dtc p0112 intake air temperature sensor 1 circuit low bank 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0112 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT LOW BANK 1DTC detecting condition:Immediately at fault recognitionTrouble symptom:• Improper idling• Poor driving performanceCAUTION:After servicing or ...
