Subaru Crosstrek Service Manual: Dtc p0970 pressure control solenoid "c" control circuit low

Subaru Crosstrek Service Manual / Continuously variable transmission (diagnostics) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0970 pressure control solenoid "c" control circuit low

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0970 PRESSURE CONTROL SOLENOID "C" CONTROL CIRCUIT LOW

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Drivability getting worse.

CAUTION:

Use the check board when measuring the TCM terminal voltage and resistance.

Wiring diagram:

CVT control system CVT Control System">

STEP	CHECK	YES	NO

1.CHECK HARNESS.

1) Turn the ignition switch to OFF.

2) Disconnect the TCM connector.

3) Disconnect the transmission connector.

4) Measure the resistance between TCM connector and chassis ground.

Connector & terminal

(B54) No. 48 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0970 PRESSURE CONTROL SOLENOID "C" CONTROL CIRCUIT LOW">Go to Step 2.

Repair the short circuit of harness.

2.CHECK AWD SOLENOID.

Measure the resistance between transmission connector and transmission body.

Connector & terminal

(T4) No. 8 — Transmission body:

Is the resistance approx. 2 — 4.5 ?? (when cold)

Check for poor contact of connector, and if no fault is found, replace the TCM. Transmission Control Module (TCM)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0970 PRESSURE CONTROL SOLENOID "C" CONTROL CIRCUIT LOW">Go to Step 3.

3.CHECK HARNESS INSIDE TRANSMISSION.

CAUTION:

Start work after ATF cools down.

1) Remove the transmission valve cover.

2) Check for the harness pinch, damage.

Is there any fault in the harness?

Replace the transmission harness.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0970 PRESSURE CONTROL SOLENOID "C" CONTROL CIRCUIT LOW">Go to Step 4.

4.CHECK HARNESS INSIDE TRANSMISSION.

1) Disconnect the control valve body connector.

2) Measure the resistance between transmission connector and transmission body.

Connector & terminal

(T4) No. 8 — Transmission body:

Is the resistance 1 M? or more?

Replace the control valve body. Control Valve Body">

Replace the transmission harness.

1. OUTLINE OF DIAGNOSIS

• Detect the GND-output short in transfer solenoid circuit.

• Judge as NG if a ground short circuit is detected more than 10 times via the detection circuit for the transfer solenoid drive circuit.

2. EXECUTION CONDITION

Secondary Parameters	Execution condition
Target duty cycle	0%

3. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Malfunction signal from solenoid driver IC	≥ 10 count

Time Needed for Diagnosis: Immediately

Malfunction Indicator Light Illumination: Does not illuminate.

Dtc p0967 pressure control solenoid "b" control circuit high

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0967 PRESSURE CONTROL SOLENOID "B" CONTROL CIRCUIT HIGHDTC detecting conditi ...

Dtc p0971 pressure control solenoid "c" control circuit high

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0971 PRESSURE CONTROL SOLENOID "C" CONTROL CIRCUIT HIGHDTC detecting conditi ...

Other materials:

Help line
The help line (distance marker and vehicle width line) is a guide to help you realize the actual distance from the screen image. 1) Vehicle width line (oblique vertical line) 2) Approx. 10 feet (3 m) from the bumper (green horizontal line) 3) Approx. 3 feet (1 m) from the bumper (yellow hor ...

Models with "keyless access with push-button start system"
NOTE For more details, refer to the Owner's Manual supplement for the remote engine start system. Access key Lock button An access key can be used as the remote engine start transmitter. Operate the lock button to start or stop the engine as follows. Before starting the engine Befo ...

Dtc p0112 intake air temperature sensor 1 circuit low bank 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0112 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT LOW BANK 1DTC detecting condition:Immediately at fault recognitionTrouble symptom:• Improper idling• Poor driving performanceCAUTION:After servicing or ...