Subaru Crosstrek Service Manual: Dtc p0962 pressure control solenoid "a" control circuit low
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC P0962 PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT LOW
DTC detecting condition:
Immediately at fault recognition
Trouble symptom:
• Engine speed increases abruptly, and can not start.
• Engine speed increases abruptly during driving.
CAUTION:
Use the check board when measuring the TCM terminal voltage and resistance.
Wiring diagram:
CVT control system CVT Control System">
| STEP | CHECK | YES | NO |
1.CHECK INPUT SIGNAL FOR TCM.
1) After driving with warm up condition, park the vehicle while depressing the brake pedal at “N” range.
2) Read the data of «Secondary Set Current» and «Secondary Actual Current» using Subaru Select Monitor.
Does the value of «Secondary Set Current» and «Secondary Actual Current» almost correspond?
Check for poor contact of connector.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0962 PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT LOW">Go to Step 2.
2.CHECK HARNESS.
1) Turn the ignition switch to OFF.
2) Disconnect the TCM connector.
3) Disconnect the transmission connector.
4) Measure the resistance between TCM connector and chassis ground.
Connector & terminal
(B54) No. 32 — Chassis ground:
Is the resistance 1 M? or more?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0962 PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT LOW">Go to Step 3.
Repair the short circuit of harness.
3.CHECK SECONDARY SOLENOID.
Measure the resistance between transmission connector and transmission body.
Connector & terminal
(T4) No. 6 — Transmission body:
Is the resistance approx. 5 — 7 ?? (when cold)
Check for poor contact of connector, and if no fault is found, replace the TCM. Transmission Control Module (TCM)">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0962 PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT LOW">Go to Step 4.
4.CHECK HARNESS INSIDE TRANSMISSION.
CAUTION:
Start work after ATF cools down.
1) Remove the transmission valve cover.
2) Check for the harness pinch, damage.
Is there any fault in the harness?
Replace the transmission harness.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0962 PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT LOW">Go to Step 5.
5.CHECK HARNESS INSIDE TRANSMISSION.
1) Disconnect the control valve body connector.
2) Measure the resistance between transmission connector and transmission body.
Connector & terminal
(T4) No. 6 — Transmission body:
Is the resistance 1 M? or more?
Replace the control valve body. Control Valve Body">
Replace the transmission harness.
1. OUTLINE OF DIAGNOSIS
Diagnosis 1
• Detect the ground short of the transmission line pressure solenoid drive circuit.
• Judge as NG if the transmission line pressure solenoid drive current is higher than the predetermined value.
Diagnosis 2
• Detect the ground short of the transmission line pressure solenoid drive circuit.
• Judge as NG when an abnormal signal is received from the solenoid driver IC of the transmission line pressure solenoid drive circuit.
2. EXECUTION CONDITION
Secondary Parameters | Execution condition |
Diagnosis 1 | |
12 V battery system voltage | ≥ 9 V |
Commanded line pressure control solenoid valve current | ≥ 0.1 A |
Diagnosis 2 | |
12 V battery system voltage | ≥ 9 V |
3. DIAGNOSTIC METHOD
If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.
Malfunction Criteria | Threshold Value |
Diagnosis 1 | |
Measured line pressure control solenoid valve current | ≥ 1.1 A |
Diagnosis 2 | |
Signal of malfunction from solenoid driver IC | ON |
As defined by: | |
Measured line pressure control solenoid valve current ≥ 1.2 A |
Time Needed for Diagnosis: 0.5 seconds
Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.
Dtc p0961 pressure control solenoid "a" control circuit range/performance
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0961 PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT RANGE/PERFORMANCEDTC DETE ...
Dtc p0963 pressure control solenoid "a" control circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0963 PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT HIGHDTC detecting conditi ...
Other materials:
Hazard warning flasher
Models without multi function display
Models with multi function display
The hazard warning flasher is used to
warn other drivers when you have to park your vehicle under emergency
conditions.
The hazard warning flasher works regardless
of the position of the ignition switch.
To ...
Dtc b28ad stereo camera image recognition
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28AD STEREO CAMERA IMAGE RECOGNITIONDetected when improper image recognition occurs in the microcomputer inside the stereo camera.DTC DETECTING CONDITION:Improper image recognition occurs in the microcomputer ins ...
Removal
EXTERIOR BODY PANELS > Front Sealing CoverREMOVAL1. Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. NOTE">2. Remove the trim panel - front door. Door Trim > REMOVAL">3. Remove the sealing cover - front door.CAUTION:• Caref ...
