Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p0842 transmission fluid pressure sensor/switch "a" circuit low

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Shift characteristics malfunction

CAUTION:

Use the check board when measuring the TCM terminal voltage and resistance.

Wiring diagram:

CVT control system CVT Control System">

STEPCHECKYESNO

1.CHECK INPUT SIGNAL FOR TCM.

1) Start the engine.

2) Warm up until the ATF temperature reaches to 40 — 70°C (104 — 158°F).

3) Depress the brake pedal, and shift the select lever to “D” range.

4) Shift the select lever to “P” range.

5) Stabilize the engine speed at idle.

6) Read the data of «Actual Secondary Pressure» using Subaru Select Monitor.

Is the «Actual Secondary Pressure» 0.5 — 1.5 MPa?

Check for poor contact of connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW">Go to Step 2.

2.CHECK HARNESS.

1) Turn the ignition switch to OFF.

2) Disconnect the TCM connector.

3) Disconnect the transmission connector.

4) Measure the resistance between TCM connector and transmission connectors.

Connector & terminal

(B54) No. 2 — (B12) No. 10:

(B54) No. 5 — (B12) No. 11:

(B54) No. 33 — (B12) No. 12:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW">Go to Step 3.

Repair the open circuit of harness.

3.CHECK HARNESS.

Measure the resistance between TCM connector and chassis ground.

Connector & terminal

(B54) No. 5 — Chassis ground:

(B54) No. 33 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW">Go to Step 4.

Repair the short circuit of harness.

4.CHECK TRANSMISSION HARNESS.

1) Disconnect the secondary pressure sensor connector.

2) Measure the resistance between transmission connector and secondary pressure sensor connector.

Connector & terminal

(T3) No. 10 — (AT6) No. 3:

(T3) No. 11 — (AT6) No. 2:

(T3) No. 12 — (AT6) No. 1:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW">Go to Step 5.

Repair the open circuit of harness.

5.CHECK TRANSMISSION HARNESS.

Measure the resistance between transmission connector and chassis ground.

Connector & terminal

(T3) No. 11 — Chassis ground:

(T3) No. 12 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0842 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT LOW">Go to Step 6.

Repair the short circuit of harness.

6.CHECK POWER SUPPLY FOR SECONDARY PRESSURE SENSOR.

1) Connect the TCM connector.

2) Connect the transmission connector.

3) Turn the ignition switch to ON.

4) Measure the voltage between secondary pressure sensor connector terminals.

Connector & terminal

(AT6) No. 1 (+) — (AT6) No. 3 (−):

Is the voltage 4.5 V or more?

Replace the secondary pressure sensor. Secondary Pressure Sensor"> If the replacement of the sensor do not eliminate the malfunction, replace the TCM. Transmission Control Module (TCM)">

Check for poor contact of connector, and if no fault is found, replace the TCM. Transmission Control Module (TCM)">

1. OUTLINE OF DIAGNOSIS

Detect the ground short circuit of the transmission line pressure sensor.

Judge as NG if the voltage detected by the transmission line pressure sensor is lower than the predetermined value.

2. EXECUTION CONDITION

Secondary Parameters

Execution condition

12 V battery system voltage

≥ 9 V

3. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

Measured line pressure sensor input voltage

< 0.195 V

(Line pressure)

(< − 574 kPa)

Time Needed for Diagnosis: 0.5 seconds

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0841 transmission fluid pressure sensor/switch "a" circuit range/performance
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0841 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT RANGE/PERFORMANCE ...

Dtc p0843 transmission fluid pressure sensor/switch "a" circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0843 TRANSMISSION FLUID PRESSURE SENSOR/SWITCH "A" CIRCUIT HIGHDTC detecting ...

Other materials:

Stowage of the cargo area cover
The cargo area cover can be stowed in under the cargo floor. 1. Raise and fold the rear end of the cargo floor board. 2. Stow the cover housing in the cargo area end. 3. Put the cargo floor board back while hanging two retaining straps on the hooks that are located on the rear wa ...

Dtc b2810 incompatible with eyesight (combination meter)
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2810 INCOMPATIBLE WITH EyeSight (COMBINATION METER)Detected when the combination meter, which is not designed exclusively for EyeSight is installed.DTC DETECTING CONDITION:Incorrect specifications of combination ...

Assembly
CONTROL SYSTEMS > Select LeverASSEMBLY1. Clean all the parts before assembly.2. Apply Multemp D or equivalent to the sliding portion of each part.3. Assemble in the reverse order of disassembly.NOTE:Insert the solenoid unit terminals to the harness connector.(A)Solenoid unit (color code: blue)(B) ...

© 2016-2024 Copyright www.sucross.com