Subaru Crosstrek Service Manual: Dtc p081a starter disable circuit low
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC P081A STARTER DISABLE CIRCUIT LOW
DTC detecting condition:
Immediately at fault recognition
Trouble symptom:
Failure of engine to start
CAUTION:
After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">
, and Inspection Mode Inspection Mode > PROCEDURE">.
Wiring diagram:
Engine electrical system Engine Electrical System">
| STEP | CHECK | YES | NO |
1.CHECK HARNESS BETWEEN STARTER RELAY (PUSH BUTTON START) CONNECTOR AND STARTER CUT RELAY CONNECTOR.
1) Turn the ignition to OFF.
2) Remove the starter relay (push button start).
3) Remove the starter cut relay.
4) Measure the resistance of harness between starter relay (push button start) connector and starter cut relay connector.
Connector & terminal
(B225) No. 28 — (B225) No. 42:
Is the resistance less than 1 ??
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P081A STARTER DISABLE CIRCUIT LOW">Go to Step 2.
Repair the open circuit in harness between starter relay (push button start) connector and starter cut relay connector.
2.CHECK HARNESS BETWEEN ECM AND STARTER CUT RELAY CONNECTOR.
1) Disconnect the connector from ECM.
2) Measure the resistance of harness between ECM connector and starter cut relay connector.
Connector & terminal
(B135) No. 34 — (B225) No. 40:
Is the resistance less than 1 ??
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P081A STARTER DISABLE CIRCUIT LOW">Go to Step 3.
Repair the open circuit of harness between ECM connector and starter cut relay connector.
3.CHECK STARTER CUT RELAY.
1) Connect the battery to starter cut relay terminals No. 40 and No. 42.
2) Measure the resistance between starter cut relay terminals.
Terminals
No. 41 — No. 44:
Is the resistance 1 M? or more?
Repair the poor contact of ECM connector.
Replace the starter cut relay. Starter Cut Relay">
1. OUTLINE OF DIAGNOSIS
Detect abnormal continuity in the starter cut relay.
Judge as NG when the starter cut relay output line is open.
2. EXECUTION CONDITION
Secondary Parameters | Execution condition |
Battery voltage | ≥ 8 V |
Engine speed | Increase from 0 rpm to 500 rpm or more |
Vehicle speed | < 1 km/h (0.6 MPH) |
Starter cut relay command | OFF |
3. GENERAL DRIVING CYCLE
Perform the diagnosis only once after the enable conditions have been established.
4. DIAGNOSTIC METHOD
Judge as NG when the following conditions are established.
Malfunction Criteria | Threshold Value |
Starter cut relay control voltage that exceeds battery voltage ? 0.34 | Not detected |
Time Needed for Diagnosis: Less than 1 second
Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.
Dtc p0700 transmission control system (mil request)
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0700 TRANSMISSION CONTROL SYSTEM (MIL REQUEST)NOTE:For the diagnostic procedure, refer to CVT section. Basi ...
Dtc p1160 throttle return spring
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P1160 THROTTLE RETURN SPRINGNOTE:For the diagnostic procedure, refer to DTC P2101. Diagnostic Procedure with ...
Other materials:
Removal
GLASS/WINDOWS/MIRRORS > Power Window Control SwitchREMOVAL1. MAIN SWITCH1. Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. NOTE">2. Remove the trim panel - front door. Door Trim > REMOVAL">3. Remove the panel - power window main ...
Operation
TELEMATICS SYSTEM (DIAGNOSTICS) > Read Current DataOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. On «Select System» display, select ...
Key lock cylinders Replacement
SECURITY AND LOCKS > Key Lock CylindersREPLACEMENT1. STEERING LOCK1. Disconnect the ground cable from battery. NOTE">2. Remove the cover assembly - column.(1) Remove the screws by turning the steering wheel to right and left.(2) Release the claw, and remove the cover assembly - column UP ...
