Subaru Crosstrek Service Manual: Dtc p0751 shift solenoid "a" performance/stuck off

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

• Shift control malfunction

• Engine speed increases abruptly.

1.CHECK DTC.

Read the DTC using Subaru Select Monitor.

Besides DTC P0751, is any of the DTCs P0973, P0974, P0976, P0977, P2747 and P2751 displayed?

Perform the diagnosis according to DTCs other than P0751.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 2.

2.CHECK PRIMARY UP SOLENOID (ACTIVE TEST).

1) Turn the ignition switch to ON.

2) Using the Subaru Select Monitor, perform forced operation of the primary UP solenoid. Active Test">

Does the indication of 0 > 50% appear repeatedly during forced operation, and does operating sound emit during indicating 50%?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 3.

3.CHECK PRIMARY UP SOLENOID.

1) Turn the ignition switch to OFF.

2) Disconnect the transmission connector.

3) Measure the resistance between transmission connector and transmission body.

Connector & terminal

(T4) No. 2 — Transmission body:

Is the resistance approx. 10 — 13.5 ?? (when cold)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 7.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 4.

4.CHECK HARNESS.

Check the transmission harness. (Open circuit, short circuit to power supply, short circuit to ground, and poor contact)

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 7.

Repair the harness.

5.CHECK TRANSMISSION FLUID.

1) Connect the transmission connector.

2) Check the amount of ATF. CVTF > ADJUSTMENT">

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 6.

Adjust the amount of ATF. CVTF > ADJUSTMENT">

6.CHECK TRANSMISSION FLUID.

Check the condition of ATF. CVTF > CONDITION CHECK">

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 7.

Check according to the “Corrective action” of ATF (CVTF) “CONDITION CHECK”. CVTF > CONDITION CHECK">

7.CHECK INPUT SIGNAL FOR TCM.

1) Lift up the vehicle.

2) Start the engine.

3) Warm up until the ATF temperature reaches to 40 — 70°C (104 — 158°F).

4) Depress the brake pedal, and shift the select lever to “D” range.

5) Shift the select lever to “P” range.

6) Stabilize the engine speed at idle.

7) Read the data of «Actual Secondary Pressure» using Subaru Select Monitor.

Is the «Actual Secondary Pressure» 0.5 — 1.5 MPa?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 8.

Replace the transmission assembly. Automatic Transmission Assembly">

8.CHECK INPUT SIGNAL FOR TCM.

1) Set the select lever to “D” range.

2) Release the brake pedal to stabilize the engine speed and front wheel speed.

3) Read the data of «Actual Gear Ratio» using Subaru Select Monitor.

Is the «Actual Gear Ratio» 1.5 — 2.6?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 9.

Replace the transmission assembly. Automatic Transmission Assembly">

9.CHECK INPUT SIGNAL FOR TCM.

1) Set the select lever to “D” range.

2) Slowly increase the speed to 40 km/h (25 MPH) and keep the constant speed.

3) Read the data of «Actual Gear Ratio» using Subaru Select Monitor.

Is the «Actual Gear Ratio» 0.5 — 0.9?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0751 SHIFT SOLENOID "A" PERFORMANCE/STUCK OFF">Go to Step 10.

Replace the transmission assembly. Automatic Transmission Assembly">

10.DRIVING CHECK BY INSPECTION MODE.

1) Turn the ignition switch to OFF.

2) Perform a drive check based on the “Inspection Mode”. Inspection Mode">

Does the AT OIL TEMP light blink and is DTC P0751 displayed?

Replace the transmission assembly. Automatic Transmission Assembly">

Current condition is normal. It is possible that temporary poor contact occurs.

• Detect the malfunction of shift-up fluid pressure control solenoid characteristics and hydraulic circuit characteristics (stuck to low pressure side).

• Judge as NG if the amount of gear rate change per second is equal to or larger than the predetermined value, even though the up-shift command is issued.

Dtc p0747 pressure control solenoid "a" stuck on

Dtc p0752 shift solenoid "a" stuck on

Other materials:

Monitor (if equipped)
To clean the audio/navigation/multi function display monitor, wipe it with a silicone cloth or with a soft cloth. If the monitor is extremely dirty, clean it with a soft cloth moistened with neutral detergent then carefully wipe off any remaining detergent. CAUTION Do not spray neutral det ...

Installation
LIGHTING SYSTEM > Headlight BulbINSTALLATIONCAUTION:Install so that the front end of the under cover (b) comes inside the bumper face - front (a), and the front end of the mud guard (c) comes outside the bumper face - front (a).1. Install each part in the reverse order of removal.2. When performi ...

Dtc p0617 starter relay "a" circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0617 STARTER RELAY "A" CIRCUIT HIGHDTC DETECTING CONDITION:Immediately at fault recognitionTROUBLE SYMPTOM:Failure of engine to startCAUTION:After servicing or replacing faulty parts, perform Clear ...