Subaru Crosstrek Service Manual: Dtc p0617 starter relay "a" circuit high

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0617 starter relay "a" circuit high

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0617 STARTER RELAY "A" CIRCUIT HIGH

DTC DETECTING CONDITION:

Immediately at fault recognition

TROUBLE SYMPTOM:

Failure of engine to start

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

WIRING DIAGRAM:

Engine electrical system Engine Electrical System">

STEP	CHECK	YES	NO

1.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check the appropriate DTC using the “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0617 STARTER RELAY "A" CIRCUIT HIGH">Go to Step 2.

2.CHECK HARNESS BETWEEN ECM AND STARTER RELAY 1 CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Turn the ignition switch to ON.

4) Measure the voltage between ECM connector and chassis ground.

Connector & terminal

(B136) No. 16 (+) — Chassis ground (−):

NOTE:

For CVT model, place the select lever in “P” range or “N” range.

Is the voltage 10 V or more?

Repair the short circuit to power in harness between ECM connector and starter relay 1 connector.

Repair the poor contact of ECM connector.

1. OUTLINE OF DIAGNOSIS

Detect abnormal continuity in the starter SW.

Judge as ON NG when the starter SW signal remains ON.

2. EXECUTION CONDITION

Secondary parameters	Execution condition
Battery voltage	≥ 8 V
Engine speed	≥ 500 rpm
Starter relay command	OFF

3. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

4. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Measured ECM input voltage which is supplied from 12 V battery system through the starter relay	≥ 12 V battery system voltage ? 0.85 V

Time Needed for Diagnosis: 30000 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0616 starter relay "a" circuit low

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0616 STARTER RELAY "A" CIRCUIT LOWDTC detecting condition:Immediately at fault recognitionCAUTION: ...

Dtc p062f internal control module eeprom error

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P062F INTERNAL CONTROL MODULE EEPROM ERRORNOTE:For the diagnostic procedure, refer to DTC P0606. Diagnostic ...

Other materials:

Update contacts from phone
Operation methods differ between PBAP (Phone Book Access Profile) compatible and PBAP incompatible but OPP (Object Push Profile) compatible Bluetooth phones. 1. Display the "PHONE" screen. Refer to "How to change the hands-free phone system" F5-73. 2. Touch the "Contacts" key, and then s ...

Inspection
COOLING(H4DO) > Radiator Fan SystemINSPECTIONOperating condition:Vehicle speedA/C compressor loadEngine coolant temperatureIncrease: 98°C (208°F) or lessDecrease: 96°C (205°F) or lessIncrease: 99 — 101°C (210 — 214°F)Decrease: ...

Inspection
STARTING/CHARGING SYSTEMS(H4DO) > GeneratorINSPECTION1. DIODECAUTION:There is the possibility of damaging the diodes if a mega-tester (used to measure high voltages) or a similar measuring instrument is used. Never use a mega tester or equivalent for this test.1. Check for continuity between the ...