ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC P0616 STARTER RELAY "A" CIRCUIT LOW
DTC detecting condition:
Immediately at fault recognition
CAUTION:
After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.
Wiring diagram:
Engine electrical system Engine Electrical System">
STEP | CHECK | YES | NO |
1.CHECK FOR ANY OTHER DTC ON DISPLAY.
Is any other DTC displayed?
Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0616 STARTER RELAY "A" CIRCUIT LOW">Go to Step 2.
2.CHECK HARNESS BETWEEN ECM AND STARTER RELAY 1 CONNECTOR.
1) Turn the ignition switch to OFF.
2) Remove the starter relay 1.
3) Disconnect the connector from ECM.
4) Disconnect the connector from starter motor.
5) Measure the resistance of harness between ECM connector and starter relay 1 connector.
Connector & terminal
(B136) No. 16 — (B225) No. 1:
NOTE:
For CVT model, place the select lever in “P” range or “N” range.
Is the resistance less than 1 ??
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0616 STARTER RELAY "A" CIRCUIT LOW">Go to Step 3.
NOTE:
Check the following item and repair or replace if necessary.
• Open circuit of harness between ECM connector and starter relay 1 connector
• Poor contact of coupling connector
3.CHECK HARNESS BETWEEN ECM AND STARTER RELAY 1 CONNECTOR.
Measure the resistance between ECM connector and chassis ground.
Connector & terminal
(B137) No. 17 — Chassis ground:
Is the resistance 1 M? or more?
Repair the poor contact of ECM connector.
Repair the short circuit to ground in harness between ECM connector and starter relay 1 connector.
1. OUTLINE OF DIAGNOSIS
Detect abnormal continuity in the starter SW.
Judge as OFF NG when the starter SW signal remains OFF.
2. EXECUTION CONDITION
Secondary Parameters | Execution condition |
Battery voltage | ≥ 8 V |
Engine speed increases from 0 to more than 500 rpm | |
Vehicle speed | < 1 km/h |
Starter relay command | ON |
3. GENERAL DRIVING CYCLE
Always perform the diagnosis continuously.
4. DIAGNOSTIC METHOD
Judge as OFF NG when the following conditions are established.
Malfunction Criteria | Threshold Value |
The ECM did not detect the following. | |
Measured ECM input voltage which is supplied from 12 V battery system through the starter relay | ≥ 12 V battery system voltage ? 0.85 V |
Time Needed for Diagnosis: Less than 1 second
Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.
Installation
LIGHTING SYSTEM > Auto Headlight Beam Leveler Control ModuleINSTALLATIONCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">Install each part in the rev ...
Dtc u0073 control module communication bus off
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0073 CONTROL MODULE COMMUNICATION BUS OFFDetected when CAN line abnormality is detected.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Procedure > PROCEDURE&qu ...
Windshield washer fluid
Windshield washer fluid warning light (type A)
Windshield washer fluid warning light (type B)
When there is only a small amount of
washer fluid remaining, the windshield
washer fluid warning light will illuminate.
When this occurs, refill the washer fluid. ...