Subaru Crosstrek Service Manual: Dtc p0506 idle control system rpm - lower than expected
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC P0506 IDLE CONTROL SYSTEM RPM - LOWER THAN EXPECTED
DTC DETECTING CONDITION:
Detected when two consecutive driving cycles with fault occur.
TROUBLE SYMPTOM:
• Hard to start the engine.
• Engine does not start
• Improper idling
• Engine stall
CAUTION:
After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">
, and Inspection Mode Inspection Mode > PROCEDURE">.
| STEP | CHECK | YES | NO |
1.CHECK FOR ANY OTHER DTC ON DISPLAY.
Is any other DTC displayed?
Check the appropriate DTC using the “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0506 IDLE CONTROL SYSTEM RPM - LOWER THAN EXPECTED">Go to Step 2.
2.CHECK AIR CLEANER ELEMENT.
1) Turn the ignition switch to OFF.
2) Check the air cleaner element.
Is there excessive clogging on air cleaner element?
Replace the air cleaner element. Air Cleaner Element">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0506 IDLE CONTROL SYSTEM RPM - LOWER THAN EXPECTED">Go to Step 3.
3.CHECK ELECTRONIC THROTTLE CONTROL.
1) Remove the electronic throttle control. Throttle Body > REMOVAL">
2) Check the electronic throttle control.
Are foreign matter found inside electronic throttle control?
Remove foreign matter from electronic throttle control.
Perform the diagnosis of DTC P2101. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P2101 THROTTLE ACTUATOR "A" CONTROL MOTOR CIRCUIT RANGE/PERFORMANCE">
1. OUTLINE OF DIAGNOSIS
Detect the malfunction that actual engine speed is not close to target engine speed during idling. Judge as NG when actual engine speed is not close to target engine speed during idling.
2. EXECUTION CONDITION
Secondary parameters | Execution condition |
Battery voltage | ≥ 10.9 V |
Barometric pressure | ≥ 75.1 kPa (563 mmHg, 22.2 inHg) |
Lambda value (left and right) | ≥ 0.85 and < 1.151 |
Vehicle speed | 0 km/h (0 MPH) |
Engine coolant temperature | ≥ 60 °C (140 °F) |
Elapsed time after starting the engine | ≥ 10 s |
Accelerator pedal position | While idling |
Elapsed time after gear position change (P ←> D or N ←> D) | > 5 s |
Cold start diagnosis | Not in operation |
Main feedback | In operation |
Idle speed control feedback | In operation |
3. GENERAL DRIVING CYCLE
Perform the diagnosis continuously at idling after warming up engine.
4. DIAGNOSTIC METHOD
If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.
Malfunction Criteria | Threshold Value |
Actual engine speed − Targeted engine speed | < −100 rpm |
Time needed for diagnosis: 15 s ? 1 time(s)
Malfunction indicator light illumination: Illuminates when malfunction occurs in 2 continuous driving cycles.
Dtc p0500 vehicle speed sensor "a" circuit
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0500 VEHICLE SPEED SENSOR "A" CIRCUITDTC DETECTING CONDITION:Immediately at fault recognitionCAUTI ...
Dtc p0507 idle control system rpm - higher than expected
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0507 IDLE CONTROL SYSTEM RPM - HIGHER THAN EXPECTEDDTC DETECTING CONDITION:Detected when two consecutive dri ...
Other materials:
Operation
GLASS/WINDOWS/MIRRORS > Power Window SystemOPERATION1. RESET OPERATION A1. Sit in the driver’s seat and close the door.2. Turn the ignition switch to ON.3. Operate the switch - power window main to open the glass assembly - front door halfway.4. Operate the switch - power window main in &ld ...
Dtc u0155 lost communication with instrument panel cluster (ipc) control module
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0155 LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULENOTE:Refer to “LAN SYSTEM (DIAGNOSTICS)” for diagnostic procedures. Basic Diagnostic Procedure" ...
Dtc b1409 scu communication
IMMOBILIZER (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1409 SCU COMMUNICATIONDTC detecting condition:Communication failure between body integrated unit and security control moduleCAUTION:When the body integrated unit is replaced, registration of the immobilizer sy ...
