Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p0336 crankshaft position sensor "a" circuit range/performance

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0336 crankshaft position sensor "a" circuit range/performance

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0336 CRANKSHAFT POSITION SENSOR "A" CIRCUIT RANGE/PERFORMANCE

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

Engine stall

Failure of engine to start

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

STEPCHECKYESNO

1.CHECK CONDITION OF CRANKSHAFT POSITION SENSOR.

Turn the ignition switch to OFF.

Is the crankshaft position sensor installation bolt tightened securely?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0336 CRANKSHAFT POSITION SENSOR "A" CIRCUIT RANGE/PERFORMANCE">Go to Step 2.

Tighten the crankshaft position sensor installation bolt securely. Crankshaft Position Sensor > INSTALLATION">

2.CHECK CRANKSHAFT POSITION SENSOR PLATE.

Is there crack or damage in the crankshaft position sensor plate teeth?

Replace the crankshaft position sensor plate. Cylinder Block">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0336 CRANKSHAFT POSITION SENSOR "A" CIRCUIT RANGE/PERFORMANCE">Go to Step 3.

3.CHECK INSTALLATION CONDITION OF TIMING CHAIN.

Turn the crankshaft using ST, and align the alignment mark on crank sprocket with alignment mark on cylinder block.

ST 18252AA000CRANKSHAFT SOCKET

Is the timing chain dislocated from its proper position?

Correct the installation condition of timing chain. Timing Chain Assembly">

Replace the crankshaft position sensor. Crankshaft Position Sensor">

1. OUTLINE OF DIAGNOSIS

Detect for faults in crankshaft position sensor output properties.

Judge as NG when there is a problem in the number of crankshaft signals for every revolution of crankshaft.

2. COMPONENT DESCRIPTION

(A)

Camshaft signal (RH)

(B)

Camshaft signal (LH)

(C)

Crankshaft signal

(1)

Crankshaft position sensor

(2)

Crankshaft position sensor plate

(3)

Crankshaft half-turn

3. EXECUTION CONDITION

Secondary Parameters

Execution condition

Battery voltage

≥ 8 V

4. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

5. DIAGNOSTIC METHOD

Judge as NG when the following conditions are established.

Judgment Value

Malfunction Criteria

Threshold Value

Amount of crank sensor signal during 1 rev of crankshaft

Not = 30

Time Needed for Diagnosis: 10 time(s) engine revs.

Malfunction Indicator Light Illumination: Illuminates when malfunction occurs in 2 continuous driving cycles.

Dtc p0335 crankshaft position sensor "a" circuit
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0335 CRANKSHAFT POSITION SENSOR "A" CIRCUITDTC DETECTING CONDITION:Immediately at fault recognitio ...

Dtc p0340 camshaft position sensor "a" circuit bank 1 or single sensor
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0340 CAMSHAFT POSITION SENSOR "A" CIRCUIT BANK 1 OR SINGLE SENSORDTC DETECTING CONDITION:Immediate ...

Other materials:

Dtc b28a6 internal stereo camera communication 1
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28A6 INTERNAL STEREO CAMERA COMMUNICATION 1Detected when communication error occurs inside the stereo camera.DTC DETECTING CONDITION:Communication error occurs inside the stereo camera.TROUBLE SYMPTOM:All functio ...

General diagnostic table Inspection
BRAKE > General Diagnostic TableINSPECTION Trouble and possible causeCorrective action1. Insufficient braking(1) Fluid leakage from the hydraulic mechanismRepair or replace. (cup, piston seal, piston boot, master cylinder piston kit, pipe or hose)(2) Entry of air into the hydraulic mechanismBleed ...

Basic information before use
WARNING When the vehicle is stopped with the engine running, always apply the parking brake for safety. Failure to do so may result in loss of control of your vehicle and cause an accident or serious injury. CAUTION To prevent damaging the screen, touch the screen keys with your finge ...

© 2016-2024 Copyright www.sucross.com