Subaru Crosstrek Service Manual: Dtc p0172 system too rich bank 1

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

• Improper idling

• Engine stall

• Poor driving performance

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

1.CHECK EXHAUST SYSTEM.

Are there holes or loose bolts on exhaust system?

Repair the exhaust system.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 2.

2.CHECK AIR INTAKE SYSTEM.

Are there holes, loose bolts or disconnection of hose on air intake system?

Repair the air intake system.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 3.

3.CHECK FUEL PRESSURE.

WARNING:

Place “NO OPEN FLAMES” signs near the working area.

Be careful not to spill fuel.

Release fuel pressure before removing the fuel pressure gauge.

Is the measured value 340 — 400 kPa (3.5 — 4.1 kg/cm2, 49 — 58 psi)?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 4.

Check the fuel pump and fuel delivery line. Fuel Pump > INSPECTION"> Fuel Delivery and Evaporation Lines > INSPECTION">

4.CHECK ENGINE COOLANT TEMPERATURE SENSOR.

1) Start the engine and warm up completely.

2) Read the value of «Coolant Temp.» using the Subaru Select Monitor or a general scan tool.

NOTE:

• Subaru Select Monitor

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

• General scan tool

For detailed operation procedures, refer to the general scan tool operation manual.

Is the value of «Coolant Temp.» 75°C (167°F) or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 5.

Replace the engine coolant temperature sensor. Engine Coolant Temperature Sensor">

5.CHECK MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR.

1) Start the engine and warm up engine until coolant temperature is higher than 75°C (167°F).

2) For CVT models, set the select lever to “P” range or “N” range, and for MT models, place the gear shift lever in the neutral position.

3) Turn the A/C switch to OFF.

4) Turn all the accessory switches to OFF.

5) Read the value of «Mass Air Flow» using the Subaru Select Monitor or a general scan tool.

NOTE:

• Subaru Select Monitor

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

• General scan tool

For detailed operation procedures, refer to the general scan tool operation manual.

Is the value of «Mass Air Flow» 2.0 — 5.0 g/s (0.26 — 0.66 lb/m)?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 6.

Replace the mass air flow and intake air temperature sensor. Mass Air Flow and Intake Air Temperature Sensor">

6.CHECK MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR.

1) Start the engine and warm up engine until coolant temperature is higher than 75°C (167°F).

2) For CVT models, set the select lever to “P” range or “N” range, and for MT models, place the gear shift lever in the neutral position.

3) Turn the A/C switch to OFF.

4) Turn all the accessory switches to OFF.

5) Open the front hood.

6) Measure the ambient temperature.

7) Read the value of «Intake Air Temp.» using the Subaru Select Monitor or a general scan tool.

NOTE:

• Subaru Select Monitor

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

• General scan tool

For detailed operation procedures, refer to the general scan tool operation manual.

Subtract ambient temperature from «Intake Air Temp.». Is the obtained value −10 — 50°C (−18 — 90°F)?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 7.

Check the mass air flow and intake air temperature sensor. Mass Air Flow and Intake Air Temperature Sensor">

7.CHECK PCV VALVE.

Check the PCV valve.

Check that the PCV valve has no deformation, cracks or other damages.

Repair or replace the PCV valve.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0172 SYSTEM TOO RICH BANK 1">Go to Step 8.

8.CHECK PCV HOSE.

Check the PCV hose.

Check the PCV hose assembly for cracks, damage or looseness.

Repair or replace the PCV hose.

Repair the poor contact of ECM connector.

Dtc p0171 system too lean bank 1

Dtc p0196 engine oil temperature sensor "a" range/performance

Other materials:

Keys
NOTE For models with "keyless access with push-button start system", refer to "Keyless access with push-button start system" 2-9. Master key Submaster key Sub key Key number plate Three types of keys are provided for your vehicle. CAUTION Do not attach a large key holder or ...

Inspection
AUTO HEADLIGHT BEAM LEVELER SYSTEM (DIAGNOSTICS) > Subaru Select MonitorINSPECTION1. COMMUNICATION FOR INITIALIZING IMPOSSIBLECommunication error with auto headlight beam leveler CMDetecting condition:• Defective harness connector• Power supply circuit malfunction• Defective aut ...

List
LAN SYSTEM (DIAGNOSTICS) > CAN Communication Circuit CheckLISTResistance value between CAN Hi and LoContents of inspectionRemarksGround short inspection CAN Communication Circuit Check > INSPECTION">Shorted to ground in the communication circuit or control module.Battery short inspecti ...