Subaru Crosstrek Service Manual: Dtc p0123 throttle/pedal position sensor/switch "a" circuit high

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0123 throttle/pedal position sensor/switch "a" circuit high

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0123 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A" CIRCUIT HIGH

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

• Improper idling

• Engine stall

• Poor driving performance

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

Wiring diagram:

Engine electrical system Engine Electrical System">

STEP	CHECK	YES	NO

1.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Disconnect the connectors from electronic throttle control.

4) Measure the resistance of harness between ECM connector and electronic throttle control connector.

Connector & terminal

(B134) No. 18 — (E57) No. 6:

(B134) No. 29 — (E57) No. 3:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0123 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A" CIRCUIT HIGH">Go to Step 2.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit in harness between ECM connector and electronic throttle control connector

• Poor contact of coupling connector

2.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Connect the connector to ECM.

2) Measure the resistance between electronic throttle control connector and engine ground.

Connector & terminal

(E57) No. 3 — Engine ground:

Is the resistance less than 5 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0123 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A" CIRCUIT HIGH">Go to Step 3.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit of harness between ECM connector and engine ground

• Poor contact of ECM connector

• Poor contact of coupling connector

3.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Turn the ignition switch to ON.

2) Measure the voltage between electronic throttle control connector and engine ground.

Connector & terminal

(E57) No. 6 (+) — Engine ground (−):

Is the voltage 5 V or more?

Repair the short circuit to power in the harness between ECM connector and electronic throttle control connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0123 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A" CIRCUIT HIGH">Go to Step 4.

4.CHECK HARNESS BETWEEN ECM AND ELECTRONIC THROTTLE CONTROL CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Measure the resistance between ECM connectors.

Connector & terminal

(B134) No. 19 — (B134) No. 18:

Is the resistance 1 M? or more?

Repair the poor contact of electronic throttle control connector. Replace the electronic throttle control if defective. Throttle Body">

Repair the short circuit to power in the harness between ECM connector and electronic throttle control connector.

1. OUTLINE OF DIAGNOSIS

Detect the open or short circuit of throttle position sensor 1.

Judge as NG if out of specification.

2. COMPONENT DESCRIPTION

(1)	Throttle position sensor 1 signal	(3)	Throttle position sensor	(4)	Engine control module (ECM)
(2)	Throttle position sensor 2 signal

3. EXECUTION CONDITION

Secondary Parameters	Execution condition
Battery voltage	≥ 6 V

4. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria	Threshold Value
Sensor 1 input voltage	≥ 4.727 V

Time Needed for Diagnosis: 24 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0122 throttle/pedal position sensor/switch "a" circuit low

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0122 THROTTLE/PEDAL POSITION SENSOR/SWITCH "A" CIRCUIT LOWDTC detecting condition:Immediately at f ...

Dtc p0131 a/f / o2 sensor circuit low voltage bank 1 sensor 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0131 A/F / O2 SENSOR CIRCUIT LOW VOLTAGE BANK 1 SENSOR 1DTC detecting condition:Immediately at fault recogni ...

Other materials:

Procedure
LIGHTING SYSTEM > Auto Headlight Beam Leveler SystemPROCEDUREWhen parts related to the auto headlight beam leveler system are removed or replaced, perform the following procedures to initialize or reinitialize.NOTE:Before performing initialization or reinitialization, check the following:• ...

List
TELEMATICS SYSTEM (DIAGNOSTICS) > System Operation Check ModeLISTSystem operation check modeNoteGREEN LED LightingGREEN LED illuminates/flashes/goes off.GREEN LED FlashingGREEN LED OFFRED LED LightingRED LED illuminates/flashes/goes off.RED LED FlashingRED LED OFFSpeaker ONOutputs to speaker. ...

If your vehicle is involved in an accident
CAUTION If your vehicle is involved in an accident, be sure to inspect the ground under the vehicle before restarting the engine. If you find that fuel has leaked on the ground, do not try to restart the engine. The fuel system has been damaged and is in need of repair. Immediately contact ...