Subaru Crosstrek Service Manual: Dtc p0113 intake air temperature sensor 1 circuit high bank 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC P0113 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH BANK 1
DTC detecting condition:
Immediately at fault recognition
Trouble symptom:
• Improper idling
• Poor driving performance
CAUTION:
After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">
, and Inspection Mode Inspection Mode > PROCEDURE">.
Wiring diagram:
Engine electrical system Engine Electrical System">
| STEP | CHECK | YES | NO |
1.CHECK CURRENT DATA.
1) Start the engine.
2) Read the value of «Intake Air Temp.» using the Subaru Select Monitor or a general scan tool.
NOTE:
• Subaru Select Monitor
For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">
• General scan tool
For detailed operation procedures, refer to the general scan tool operation manual.
Is the value of «Intake Air Temp.» −40°C (−40°F) or less?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0113 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH BANK 1">Go to Step 2.
Even if DTC is detected, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
NOTE:
In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.
2.CHECK FOR POOR CONTACT.
Check for poor contact of ECM and mass air flow and intake air temperature sensor connector.
Is there poor contact of ECM or mass air flow and intake air temperature sensor connector?
Repair the poor contact of ECM or mass air flow and intake air temperature sensor connector.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0113 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH BANK 1">Go to Step 3.
3.CHECK HARNESS BETWEEN ECM AND MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from ECM.
3) Disconnect the connectors from the mass air flow and intake air temperature sensor.
4) Measure the resistance of harness between ECM connector and the mass air flow and intake air temperature sensor connector.
Connector & terminal
(B137) No. 12 — (B3) No. 1:
(B137) No. 30 — (B3) No. 2:
Is the resistance less than 1 ??
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0113 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT HIGH BANK 1">Go to Step 4.
Repair the harness and connector.
NOTE:
In this case, repair the following item:
• Open circuit in harness between ECM connector and the mass air flow and intake air temperature sensor connector
• Poor contact of joint connector
4.CHECK HARNESS BETWEEN ECM AND MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR CONNECTOR.
1) Connect all connectors.
2) Turn the ignition switch to ON.
3) Measure the voltage between ECM connector and chassis ground.
Connector & terminal
(B137) No. 12 (+) — Chassis ground (−):
Is the voltage 5 V or more?
Repair the short circuit of harness to power supply between ECM connector and the mass air flow and intake air temperature sensor connector.
Replace the mass air flow and intake air temperature sensor. Mass Air Flow and Intake Air Temperature Sensor">
1. OUTLINE OF DIAGNOSIS
Detect open or short circuit of the intake air temperature sensor.
Judge as NG if out of specification.
2. COMPONENT DESCRIPTION
(A) | Air | ||||
(1) | Air flow sensor | (3) | Resistance value (?) | (4) | Intake air temperature °C (°F) |
(2) | Intake air temperature sensor |
3. EXECUTION CONDITION
Secondary Parameters | Execution condition |
None |
4. GENERAL DRIVING CYCLE
Always perform the diagnosis continuously.
5. DIAGNOSTIC METHOD
If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.
Malfunction Criteria | Threshold Value |
Output voltage | ≥ 4.707 V |
Time Needed for Diagnosis: 500 ms
Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.
Dtc p0112 intake air temperature sensor 1 circuit low bank 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0112 INTAKE AIR TEMPERATURE SENSOR 1 CIRCUIT LOW BANK 1DTC detecting condition:Immediately at fault recognit ...
Dtc p0116 engine coolant temperature sensor 1 circuit range/performance
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0116 ENGINE COOLANT TEMPERATURE SENSOR 1 CIRCUIT RANGE/PERFORMANCEDTC DETECTING CONDITION:Detected when two ...
Other materials:
Assembly
DRIVE SHAFT SYSTEM > Rear Hub Unit BearingASSEMBLY1. Install the rear hub unit bearing to the ST securely.Preparation tool:ST: HUB STAND (927080000)(1)Rear hub unit bearing2. Using a press, press new hub bolts (b) until their seating surfaces contact the rear hub unit bearing (a).NOTE:Use the 12 ...
Removal
SECURITY AND LOCKS > Push Button Ignition SwitchREMOVALCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">1. Disconnect the ground cable from battery a ...
Assembly
BRAKE > Front Disc Brake AssemblyASSEMBLY1. Before assembly, check each part. Front Disc Brake Assembly > INSPECTION">2. Clean the inside of the caliper body cylinder using brake fluid.3. Apply a coat of brake fluid to piston seal and install the piston seal to the caliper body cylind ...
