Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p0103 mass or volume air flow sensor "a" circuit high

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0103 MASS OR VOLUME AIR FLOW SENSOR "A" CIRCUIT HIGH

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Improper idling

Engine stall

Poor driving performance

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

Wiring diagram:

Engine electrical system Engine Electrical System">

STEPCHECKYESNO

1.CHECK CURRENT DATA.

1) Start the engine.

2) Read the value of «Air Flow Sensor Voltage» using Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

Is the value of «Air Flow Sensor Voltage» 5 V or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0103 MASS OR VOLUME AIR FLOW SENSOR "A" CIRCUIT HIGH">Go to Step 2.

Even if DTC is detected, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.CHECK HARNESS BETWEEN ECM AND MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connectors from the mass air flow and intake air temperature sensor.

3) Start the engine.

4) Read the value of «Air Flow Sensor Voltage» using Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

Is the value of «Air Flow Sensor Voltage» 5 V or more?

Repair the short circuit of harness to power supply between ECM connector and the mass air flow and intake air temperature sensor connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0103 MASS OR VOLUME AIR FLOW SENSOR "A" CIRCUIT HIGH">Go to Step 3.

3.CHECK HARNESS BETWEEN ECM AND MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR CONNECTOR.

1) Turn the ignition switch to OFF.

2) Measure the resistance of harness between mass air flow and intake air temperature sensor connector and engine ground.

Connector & terminal

(B3) No. 4 — Engine ground:

Is the resistance less than 5 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0103 MASS OR VOLUME AIR FLOW SENSOR "A" CIRCUIT HIGH">Go to Step 4.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

Open circuit in harness between ECM connector and the mass air flow and intake air temperature sensor connector

Poor contact of ECM connector

4.CHECK FOR POOR CONTACT.

Check for poor contact of mass air flow and intake air temperature sensor connector.

Is there poor contact of mass air flow and intake air temperature sensor connector?

Repair the poor contact of mass air flow and intake air temperature sensor connector.

Replace the mass air flow and intake air temperature sensor. Mass Air Flow and Intake Air Temperature Sensor">

1. OUTLINE OF DIAGNOSIS

Detect open or short circuits of the air flow sensor.

Judge as NG if out of specification.

2. COMPONENT DESCRIPTION

(A)

Air

(1)

Air flow sensor

(3)

Voltage (V)

(4)

Intake air amount (kg (lb)/s)

(2)

Intake air temperature sensor

3. EXECUTION CONDITION

Secondary Parameters

Execution condition

None

4. GENERAL DRIVING CYCLE

Always perform the diagnosis continuously.

5. DIAGNOSTIC METHOD

If the duration of time while the following conditions are met is longer than the time indicated, judge as NG.

Judgment Value

Malfunction Criteria

Threshold Value

Output voltage

≥ 4.43 V

Time Needed for Diagnosis: 500 ms

Malfunction Indicator Light Illumination: Illuminates as soon as a malfunction occurs.

Dtc p0102 mass or volume air flow sensor "a" circuit low
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0102 MASS OR VOLUME AIR FLOW SENSOR "A" CIRCUIT LOWDTC detecting condition:Immediately at fault re ...

Dtc p0107 manifold absolute pressure/barometric pressure sensor circuit low
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0107 MANIFOLD ABSOLUTE PRESSURE/BAROMETRIC PRESSURE SENSOR CIRCUIT LOWDTC detecting condition:Immediately at ...

Other materials:

Installation
DRIVE SHAFT SYSTEM > Rear Hub Unit BearingINSTALLATION1. Place the rear brake back plate between the rear axle housing and the rear hub unit bearing, and tighten the bolt.CAUTION:• Be careful not to damage the magnetic encoder.• Do not get closer the tool which charged magnetism to ma ...

Two separate circuits
Your vehicle has two separate circuit brake systems. Each circuit works diagonally across the vehicle. If one circuit of the brake system should fail, the other half of the system still works. If one circuit fails, the brake pedal will go down much closer to the floor than usual and you will n ...

Fuel filler lid and cap
Locations of the fuel filler lid and the lid release lever Fuel filler lid Fuel filler lid release lever Refueling Only one person should be involved in refueling. Do not allow others to approach the area of the vehicle near the fuel filler pipe while refueling is in progress. Be ...

© 2016-2024 Copyright www.sucross.com