Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p0019 crankshaft position - camshaft position correlation bank 2 sensor b

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0019 crankshaft position - camshaft position correlation bank 2 sensor b

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

Engine stall

Improper idling

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

STEPCHECKYESNO

1.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is DTC other than P0016, P0017, P0018 or P0019 displayed?

Check the appropriate DTC using the “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 2.

2.CHECK EXHAUST OIL CONTROL SOLENOID LH.

Check the exhaust oil control solenoid LH. Oil Control Solenoid > INSPECTION">

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 3.

Replace the exhaust oil control solenoid LH. Oil Control Solenoid">

3.CHECK INSTALLATION CONDITION OF TIMING CHAIN.

Using ST and by turning the crankshaft, align the alignment marks of crank sprocket, intake cam sprocket and exhaust cam sprocket. Timing Chain Assembly">

ST 18252AA000CRANKSHAFT SOCKET

Is the timing chain installed in the proper position?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 4.

Correct the installation condition of timing chain. Timing Chain Assembly">

4.CHECK CAM CARRIER FILTER.

Check the filter installed to the cam carrier. Cam Carrier > INSPECTION">

Is the check result OK?

Replace the exhaust cam sprocket LH. Cam Sprocket"> After the operation is complete, go to the next step. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 5.

Replace the cam carrier filter. Cam Carrier">

5.CHECK CURRENT DATA.

1) Clear the memory using the Subaru Select Monitor or general scan tool. Clear Memory Mode > OPERATION">

2) Start the engine and warm up completely.

3) Using the Subaru Select Monitor, read the values of «VVT Ex Initial Position Learning Value #2» and «Exh. VVT Retard Ang. L» while the vehicle is in stable condition for 30 seconds or more with the engine idling.

NOTE:

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

4) Calculate the values using the following formula. Ignore the unit at this time.

|«VVT Ex Initial Position Learning Value #2» − (90 − «Exh. VVT Retard Ang. L»)|

Is the calculation result less than 10?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0019 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B">Go to Step 6.

Replace the ECM. Engine Control Module (ECM)">

6.CHECK DTC.

1) Clear the memory using the Subaru Select Monitor or general scan tool. Clear Memory Mode > OPERATION">

2) Perform drive cycle N. Drive Cycle > PROCEDURE">

Is the same DTC as current diagnosis output?

Replace the ECM. Engine Control Module (ECM)">

End.

1. OUTLINE OF DIAGNOSIS

NOTE:

For the detection standard, refer to DTC P0017. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0017 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 1 SENSOR B">

Dtc p0018 crankshaft position - camshaft position correlation bank 2 sensor a
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0018 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 2 SENSOR ADTC detecting condition:Detected whe ...

Dtc p0020 "a" camshaft position actuator control circuit/open bank 2
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0020 "A" CAMSHAFT POSITION ACTUATOR CONTROL CIRCUIT/OPEN BANK 2DTC detecting condition:Immediately ...

Other materials:

Drive cycle Procedure
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Drive CyclePROCEDUREIt is possible to complete diagnosis of the DTC by performing the indicated drive cycle. After the repair for the DTC, perform a necessary drive cycle and make sure the function recovers and the DTC is recorded.1. PREPARATION ...

Dtc b1571 reference code incompatibility (immobilizer cm to ecm)
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1571 REFERENCE CODE INCOMPATIBILITY (IMMOBILIZER CM TO ECM)DTC detecting condition:Incompatibility of reference code between keyless access CM (model without ID code box) or ID ...

Disassembly
SEATS > Front SeatDISASSEMBLY1. DRIVER’S SEATCAUTION:Before assembling, make sure how the harnesses such as the side airbag harness and the seat belt inner - front harness are routed in order to avoid misarranging. Assembling with harnesses improperly routed may cause the harness to get cau ...

© 2016-2024 Copyright www.sucross.com