Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc p0014 "b" camshaft position - timing over-advanced or system performance bank 1

Subaru Crosstrek Service Manual / Engine (diagnostics)(h4do) / Diagnostic procedure with diagnostic trouble code (dtc) / Dtc p0014 "b" camshaft position - timing over-advanced or system performance bank 1

ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC P0014 "B" CAMSHAFT POSITION - TIMING OVER-ADVANCED OR SYSTEM PERFORMANCE BANK 1

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

Engine stall

Improper idling

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

STEPCHECKYESNO

1.IDENTIFYING FAULTY PART.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Replace the defective oil control solenoid by the other (RH or LH, intake side or exhaust side) oil control solenoid.

3) Perform appropriate drive cycle test. Drive Cycle">

4) Make sure that the fault occurrence (DTC and incorrect advancing) has shifted to the other location.

Did the detected DTC shift to the location where the oil control solenoid was replaced?

Replace the faulty oil control solenoid.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0014 "B" CAMSHAFT POSITION - TIMING OVER-ADVANCED OR SYSTEM PERFORMANCE BANK 1">Go to Step 2.

2.CHECK CURRENT DATA.

1) Start the engine and let it idle.

2) Read the value of «Exh. VVT Retard Ang. R» using the Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

Is the value of «Exh. VVT Retard Ang. R» approx. 0 deg?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0014 "B" CAMSHAFT POSITION - TIMING OVER-ADVANCED OR SYSTEM PERFORMANCE BANK 1">Go to Step 3.

Check the following item and repair or replace if necessary.

Exhaust cam sprocket (clog or dirt of oil routing, setting of spring)

Exhaust camshaft (dirt, damage of camshaft)

3.CHECK CURRENT DATA.

1) Drive with acceleration and deceleration at 80 km/h (50 MPH) or less.

NOTE:

Drive to an extent that the duty output of oil flow control solenoid valve increases.

2) Read the values of «Exh. OCV Duty R» and «Exh. VVT Retard Ang. R» using the Subaru Select Monitor.

NOTE:

For detailed operation procedures, refer to “Current Data Display For Engine”. Subaru Select Monitor">

When the value of «Exh. OCV Duty R» increases more than 10%, is the value of «Exh. VVT Retard Ang. R» approx. 0 deg?

Check the following item and repair or replace if necessary.

Exhaust cam sprocket (clog or dirt of oil routing, setting of spring)

Exhaust camshaft (dirt, damage of camshaft)

Perform the following procedures, and clean the oil routing.

Replace the engine oil and idle the engine for 5 minutes, and then replace the oil filter and engine oil. Engine Oil > REPLACEMENT"> Engine Oil Filter">

1. OUTLINE OF DIAGNOSIS

Detect the exhaust AVCS system malfunction.

Judge as NG when the conditions during which the differences of exhaust AVCS target timing advance amount and exhaust AVCS actual timing advance amount is large continues.

2. EXECUTION CONDITION

Secondary Parameters

Execution condition

Battery voltage

≥ 10.9 V

Exhaust AVCS control

In operation

3. GENERAL DRIVING CYCLE

Perform the diagnosis continuously when the engine speed increases and exhaust AVCS operates.

4. DIAGNOSTIC METHOD

When the conditions during which the differences of exhaust AVCS target timing advance amount and exhaust AVCS actual timing advance amount is large continues for certain amount of time.

Judge as NG when the following conditions are established within the predetermined time.

Judgment value

Malfunction Criteria

Threshold Value

|(Target position − Actual position)|

> 10 °CA

Time needed for diagnosis: 10000 ms

Malfunction indicator light illumination: Illuminates when malfunction occurs in 2 continuous driving cycles.

Dtc p0013 "b" camshaft position actuator control circuit/open bank 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0013 "B" CAMSHAFT POSITION ACTUATOR CONTROL CIRCUIT/OPEN BANK 1DTC detecting condition:Immediately ...

Dtc p0016 crankshaft position - camshaft position correlation bank 1 sensor a
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0016 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 1 SENSOR ADTC detecting condition:Detected whe ...

Other materials:

Removal
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Transmission HarnessREMOVAL1. INHIBITOR HARNESS1. Remove the transmission from the vehicle. Automatic Transmission Assembly > REMOVAL">2. Remove the transmission case cover.3. Remove the harness connector from the ground terminal, turbine sp ...

Location
VEHICLE DYNAMICS CONTROL (VDC) > Relay and FuseLOCATIONMain fuse boxFuse 50A (VDC CM&H/U)(A)Fuse 30A (VDC CM&H/U)(B)NOTE:For other related fuses, refer to the wiring diagram. Power Supply Circuit"> ...

Preparation tool
GLASS/WINDOWS/MIRRORS > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS — SUBARU SELECT MONITOR 4Used for setting of each function and troubleshooting for electrical system.NOTE:For detailed operation procedures of Subaru Select Monitor 4, refer to &l ...

© 2016-2024 Copyright www.sucross.com