Subaru Crosstrek Service Manual: Dtc c2224 transmitter 4 pressure data abnormal

DTC DETECTING CONDITION:

Detected when error data is received from each transmitter at a vehicle speed of 40 km/h (25 MPH) or more.

• When comparing the data from each transmitter to the previous data, the change is large.

• The pressure exceeds what the transmitter can measure. (Excessive pressure)

1.REPRODUCTION OF FAILURE.

1) Perform the drive test.

Drive the vehicle at 40 km/h (25 MPH) or faster for at least 10 minutes.

2) Read the DTC of tire pressure monitoring. Read Diagnostic Trouble Code (DTC) > OPERATION">

Is DTC displayed as “Present fault”?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 2.

When DTC is displayed as “Past faults”, the system has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, there may be temporary poor communication due to radio wave environment inside/outside the vehicle.

2.START FRONT LEFT TRANSMITTER.

1) Connect the Subaru Select Monitor and then turn the ignition switch to ON.

2) Select «Data monitor» of the tire pressure monitor. Read Current Data">

3) Use the transmitter registration tool and transmit the ID from the front left transmitter to check «Latest reception ID».

Is «Latest reception ID» updated?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 3.

Replace the front left transmitter. Tire Pressure Monitoring System">

3.CHECK FRONT LEFT TRANSMITTER ID.

Compare the ID on the latest ID display with «Registered ID 1».

Are the two IDs same?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 4.

Record «Latest reception ID» as the front left. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 4.

4.START FRONT RIGHT TRANSMITTER.

Use the transmitter registration tool and transmit the ID from the front right transmitter to check «Latest reception ID».

Is «Latest reception ID» updated?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 5.

Replace the front right transmitter. Tire Pressure Monitoring System">

5.CHECK FRONT RIGHT TRANSMITTER ID.

Compare the ID on the latest ID display with «Registered ID 2».

Are the two IDs same?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 6.

Record «Latest reception ID» as the front right. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 6.

6.START REAR RIGHT TRANSMITTER.

Use the transmitter registration tool and transmit the ID from the rear right transmitter to check «Latest reception ID».

Is «Latest reception ID» updated?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 7.

Replace the rear right transmitter. Tire Pressure Monitoring System">

7.CHECK REAR RIGHT TRANSMITTER ID.

Compare the ID on the latest ID display with «Registered ID 3».

Are the two IDs same?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 8.

Record «Latest reception ID» as the rear right. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 8.

8.START REAR LEFT TRANSMITTER.

Use the transmitter registration tool and transmit the ID from the rear left transmitter to check «Latest reception ID».

Is «Latest reception ID» updated?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 9.

Replace the rear left transmitter. Tire Pressure Monitoring System">

9.CHECK REAR LEFT TRANSMITTER ID.

Compare the ID on the latest ID display with «Registered ID 4».

Are the two IDs same?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 10.

Record «Latest reception ID» as the rear left. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 10.

10.CHECK MALFUNCTION TRANSMITTER.

Is ID recorded by this procedure?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 11.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2224 TRANSMITTER 4 PRESSURE DATA ABNORMAL">Go to Step 2.

11.CHECK MALFUNCTION TRANSMITTER.

Check the registered ID of the transmitter indicated by DTC.

Is there checked ID in the record?

Replace the transmitter of the recorded position. Tire Pressure Monitoring System">

Replace the transmitter showing the latest ID that is not included in the registered IDs. Tire Pressure Monitoring System">

Dtc c2223 transmitter 3 pressure data abnormal

Dtc c2321 transmitter 1 function code abnormal

Other materials:

Installation
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Knock SensorINSTALLATION1. Install the knock sensor to the cylinder block.NOTE:The knock sensor should be installed so that the center of the connector is positioned at a 76.5 — 91.5° angle relative to the front of engine.Tightening torque:24 N&m ...

Dtc p0117 engine coolant temperature sensor 1 circuit low
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0117 ENGINE COOLANT TEMPERATURE SENSOR 1 CIRCUIT LOWDTC detecting condition:Immediately at fault recognitionTrouble symptom:• Hard to start• Improper idling• Poor driving performanceCAUTION: ...

Installation
AIRBAG SYSTEM > Roll ConnectorINSTALLATIONCAUTION:If the steering wheel and steering angle sensor (steering roll connector) are removed, be sure to perform the following operations.• Align the center position of the steering roll connector.• Perform the neutral position setting of the ...