Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc c1811 system

VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC C1811 SYSTEM

DTC detecting condition:

ABS and VDC long time sequential control

Trouble symptom:

ABS does not operate.

VDC does not operate.

EBD may not operate.

Hill start assist does not operate.

STEPCHECKYESNO

1.CHECK INSTALLATION OF VDCCM&H/U.

Is VDCCM&H/U installed properly without being tilted?
Is the bracket deformation-free?
Are the VDCCM&H/U installation bolts installed without missing or getting loose?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 2.

Repair the defective part.

Install VDCCM&H/U properly.

Replace the bracket if faulty.

Tighten the VDCCM&H/U installation bolt. General Description > COMPONENT">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 2.

2.CHECK STEERING WHEEL.

1) Drive the vehicle on a flat road.

2) Park the vehicle straight.

3) Check the steering wheel for deviation from center.

Is the deviation from the center of steering wheel less than 5°?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 3.

Perform the centering adjustment of steering wheel, and perform the VDC sensor midpoint setting mode. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 3.

3.CHECK OUTPUT OF STEERING ANGLE SENSOR USING SUBARU SELECT MONITOR.

1) Adjust steering wheel to the center position.

2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

3) Read the «Steering Angle Sensor» displayed on display.

Is the reading of «Steering Angle Sensor» −10° — 10°?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 4.

Check the installation of the steering wheel and steering angle sensor, and correct the installation if it is improper. If the installation condition is correct, replace the sensor.

4.CHECK OUTPUT OF SENSORS USING SUBARU SELECT MONITOR.

1) Drive the vehicle on a flat road.

2) Park the vehicle straight.

3) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

4) Read «Lateral G Sensor», «Longitudinal G Sensor», and «Yaw Rate Sensor» displayed on display.

Is the reading of each sensor following value?
«Lateral G Sensor»: −2 — 2 m/s2
«Longitudinal G Sensor»: −2 — 2 m/s2
«Yaw Rate Sensor»: −4 deg/s — 4 deg/s

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 5.

Recheck from step 1, and if the problem is not solved, Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 8.

5.SET 0 POINT FOR LONGITUDINAL G SENSOR USING SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Work Support”.

2) Perform the VDC sensor midpoint setting mode. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">

Is the 0 point setting successful?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 6.

Recheck from step 1, and when the 0 point setting is not possible, replace the VDCCM and the steering angle sensor. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT"> Steering Angle Sensor">

6.PERFORM DRIVING TEST.

Drive approximately 10 minutes, and check if the warning lights illuminate or improperly operate during driving.

Did the ABS warning light or VDC warning light remain off?
Does ABS or VDC operate without malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1811 SYSTEM">Go to Step 7.

Recheck from step 1, and when the warning lights illuminate or improperly operate, replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

7.CHECK OUTPUT OF SENSORS USING SUBARU SELECT MONITOR.

1) Park the vehicle on a level surface.

2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

3) Read «Lateral G Sensor», «Longitudinal G Sensor», and «Yaw Rate Sensor» displayed on display.

Is the reading of each sensor following value?
«Lateral G Sensor»: −2 — 2 m/s2
«Longitudinal G Sensor»: −2 — 2 m/s2
«Yaw Rate Sensor»: −4 deg/s — 4 deg/s

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

8.CHECK OUTPUT OF SENSORS USING SUBARU SELECT MONITOR.

1) Remove the VDCCM&H/U installation bolt and bracket.

2) Keep VDCCM&H/U in a horizontal position.

3) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

4) Read «Lateral G Sensor», «Longitudinal G Sensor», and «Yaw Rate Sensor» displayed on display.

When VDCCM&H/U is in a horizontal position, is the reading of each sensor following value?
«Lateral G Sensor»: −1.5 — 1.5 m/s2
«Longitudinal G Sensor»: −1.5 — 1.5 m/s2
«Yaw Rate Sensor»: −4 deg/s — 4 deg/s

Check the bracket and brake pipe, and install VDCCM&H/U in a horizontal position to the vehicle.

Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

Dtc c1733 longitudinal g sensor
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C1733 LONGITUDINAL G SENSORDTC DETECTING CONDITION:Defective longitudinal G sensorTROUBLE S ...

Dtc c0046 body integrated module communication circuit
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0046 BODY INTEGRATED MODULE COMMUNICATION CIRCUITDTC detecting condition:No CAN signal rec ...

Other materials:

Removal
FRONT SUSPENSION > Front StrutREMOVAL1. Lift up the vehicle, and then remove the front wheels.2. Remove the front strut assembly.(1) Place an alignment mark (a) on the adjusting bolt and the strut.(2) Remove the brake hose bracket.(3) Remove the clamp of ABS wheel speed sensor harness.(4) Remove ...

Disassembly
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Transmission CaseDISASSEMBLY1. Remove the oil stopper plate.2. Remove all plugs from the transmission case.3. Remove the oil seal using a screwdriver wrapped with cloth etc.4. Using the ST, remove the ball bearing of the secondary pulley.(1) Remove the ...

Dtc p0203 cylinder 3 injector "a" circuit
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0203 CYLINDER 3 INJECTOR "A" CIRCUITNOTE:For the diagnostic procedure, refer to DTC P0201. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0201 CYLINDER 1 INJECTOR "A" C ...

© 2016-2024 Copyright www.sucross.com