Subaru Crosstrek Service Manual: Dtc c1741 pressure sensor

DTC detecting condition:

Defective pressure sensor

Trouble symptom:

• ABS does not operate.

• VDC does not operate.

• Hill start assist does not operate.

1.CHECK STOP LIGHT SWITCH CIRCUIT AND INSTALLATION CONDITION.

Check the stop light switch circuit and the installation condition.

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1741 PRESSURE SENSOR">Go to Step 2.

Repair the stop light switch circuit or correct the installation condition.

NOTE:

If there is malfunction in the stop light circuit, DTC may be recorded in the memory.

2.CHECK OUTPUT OF PRESSURE SENSOR WITH SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

2) Read the «Master Cylinder Pressure Sensor» displayed on display.

With the brake pedal released, does the value for «Master Cylinder Pressure Sensor» fall within 0 — 11 bar?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1741 PRESSURE SENSOR">Go to Step 3.

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

3.CHECK OUTPUT OF PRESSURE SENSOR WITH SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

2) Read the «Master Cylinder Pressure Sensor» displayed on display.

When the brake pedal is operated, does the value of «Master Cylinder Pressure Sensor» change in accordance with the brake pedal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1741 PRESSURE SENSOR">Go to Step 4.

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

4.CHECK VDCCM&H/U.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Perform the Inspection Mode. Inspection Mode">

3) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1741 PRESSURE SENSOR">Go to Step 5.

5.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c0073 abnormal lateral g sensor output

Dtc c1251 wheel speed sensor system

Other materials:

Removal
WIPER AND WASHER SYSTEMS > Front Washer Nozzle and HoseREMOVAL1. NOZZLE - WINDSHIELD WASHER & HOSE1. Remove the arm assembly - windshield wiper. Front Wiper Arm > REMOVAL">2. Remove the cowl panel - side and the cowl panel assembly. Cowl Panel > REMOVAL">CAUTION:Before ...

Removal
CRUISE CONTROL SYSTEM > Cruise Control Command SwitchREMOVALCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">1. Set the tire to the straight-ahead po ...

Inspection
EyeSight > Relay and FuseINSPECTION1. CHECK FUSE1. Remove the fuse and inspect visually.2. If the fuse is blown out, replace the fuse.NOTE:If the fuse is blown again, check the system wiring harness.2. CHECK RELAY1. Measure the resistance between relay terminals.Terminal No.Inspection conditionsS ...