Subaru Crosstrek Service Manual: Dtc c1732 lateral g sensor

DTC detecting condition:

Defective lateral G sensor

Trouble symptom:

• ABS does not operate.

• VDC does not operate.

• Hill start assist does not operate.

1.CHECK INSTALLATION OF VDCCM&H/U.

Is VDCCM&H/U installed properly without being tilted?
Is the bracket deformation-free?
Are the VDCCM&H/U installation bolts installed without missing or getting loose?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 2.

Repair the defective part.

• Install VDCCM&H/U properly.

• Replace the bracket if faulty.

• Tighten the VDCCM&H/U installation bolt. General Description > COMPONENT">

2.CHECK OUTPUT OF STEERING ANGLE SENSOR USING SUBARU SELECT MONITOR.

1) Park the vehicle straight on a level surface.

2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

3) Read the «Steering Angle Sensor» displayed on display.

Is the reading of «Steering Angle Sensor» −10 — 10°?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 3.

Check the installation of steering angle sensor.

3.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR.

1) Park the vehicle straight on a level surface.

2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

3) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display.

Are the values of «Lateral G Sensor»«Longitudinal G Sensor» −2 — 2 m/s2?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 4.

Recheck from step 1, and if the problem is not solved, Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 7.

4.SET 0 POINT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Work Support”.

2) Perform the VDC sensor midpoint setting mode. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > ADJUSTMENT">

Is the 0 point setting successful?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 5.

Recheck from step 1, and when the 0 point setting is not possible, replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

5.PERFORM DRIVING TEST.

Drive approximately 10 minutes, and check if the warning lights illuminate or improperly operate during driving.

In a safe place, drive the vehicle while alternating acceleration and deceleration as much as possible.

Did the ABS warning light or VDC warning light remain off?
Does ABS or VDC operate without malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1732 LATERAL G SENSOR">Go to Step 6.

Recheck from step 1, and when the warning lights illuminate or improperly operate, replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

6.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR.

1) Park the vehicle on a level surface.

2) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

3) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display.

Are the values of «Lateral G Sensor»«Longitudinal G Sensor» −1.5 — 1.5 m/s2?

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Recheck from step 1, and if the problem is not solved, replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

7.CHECK OUTPUT OF LATERAL G SENSOR AND LONGITUDINAL G SENSOR WITH SUBARU SELECT MONITOR.

1) Remove the VDCCM&H/U installation bolt and bracket.

2) Keep VDCCM&H/U in a horizontal position.

3) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

4) Read the «Lateral G Sensor» «Longitudinal G Sensor» displayed on display.

When the VDCCM&H/U is in a horizontal position, are the values of «Lateral G Sensor»«Longitudinal G Sensor» −1.5 — 1.5 m/s2?

Check the bracket and brake pipe, and install VDCCM&H/U in a horizontal position to the vehicle.

Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

Dtc c1721 yaw rate sensor

Dtc c1733 longitudinal g sensor

Other materials:

Tripped sensor identification
The security indicator light flashes when the alarm system has been triggered. Also, the number of flashes indicates the location of unauthorized intrusion or the severity of impact on the vehicle. When the ignition switch is turned to the "ON" position, the indicator light will light for ...

Installation
EXTERIOR BODY PANELS > Front HoodINSTALLATIONCAUTION:The hood COMPL - front is heavy. When removing or installing the hinge COMPL - front hood, be sure to work in a group of two or more.1. To install the insulator - front hood and the seal - front duct, follow the removal procedure in the reverse ...

Installation
ENTERTAINMENT > AudioINSTALLATIONCAUTION:• After installing the center grille assembly, check that the air vent grille of the center grille assembly is inserted correctly into the air vent duct.• Before handling the airbag system components, refer to “CAUTION” of “Ge ...