Subaru Crosstrek Service Manual: Dtc c1721 yaw rate sensor

DTC DETECTING CONDITION:

Defective yaw rate & G sensor

TROUBLE SYMPTOM:

• ABS does not operate.

• VDC does not operate.

• Hill start assist does not operate.

1.INTERVIEW CUSTOMERS.

Check if the vehicle ran the road with banks or sandy surface (which does not mean a dirt road).

Did the vehicle run the road with banks or sandy surface (which does not mean a dirt road)?

VDCCM&H/U may record DTC when the vehicle ran the road with banks or sandy surface (which does not mean a dirt road).

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1721 YAW RATE SENSOR">Go to Step 2.

2.CHECK INSTALLATION OF VDCCM&H/U.

Is VDCCM&H/U installed properly without being tilted?
Is the bracket deformation-free?
Are the VDCCM&H/U installation bolts installed without missing or getting loose?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1721 YAW RATE SENSOR">Go to Step 3.

Repair the defective part.

• Install VDCCM&H/U properly.

• Replace the bracket if faulty.

• Tighten the VDCCM&H/U installation bolt. General Description > COMPONENT">

3.CHECK OUTPUT OF YAW RATE & G SENSOR WITH SUBARU SELECT MONITOR.

1) Drive the vehicle on a flat road.

2) Park the vehicle straight.

3) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

4) Read the «Yaw Rate Sensor» displayed on display.

Is the reading of «Yaw Rate Sensor» −4 deg/s — 4 deg/s?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1721 YAW RATE SENSOR">Go to Step 4.

Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

4.CHECK OUTPUT OF STEERING ANGLE SENSOR WITH SUBARU SELECT MONITOR.

1) Drive the vehicle on a flat road.

2) Park the vehicle straight.

3) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

4) Read the «Steering Angle Sensor» displayed on display.

Is the reading of «Steering Angle Sensor» −10° — 10°?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1721 YAW RATE SENSOR">Go to Step 5.

Perform the centering adjustment of steering wheel.

5.CHECK VDCCM&H/U.

1) Turn the ignition switch to OFF.

2) Perform the Clear Memory Mode. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1721 YAW RATE SENSOR">Go to Step 6.

6.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c1711 steering angle sensor

Dtc c1732 lateral g sensor

Other materials:

Dtc b28b1 stereo camera automatic adjustment
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28B1 STEREO CAMERA AUTOMATIC ADJUSTMENTDetected when the optical axis of stereo camera is deviated in lateral direction or when the fluctuation range of automatic adjustment value has expanded.NOTE:Readjust the s ...

Dtc c1212 front right abs sensor signal
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C1212 FRONT RIGHT ABS SENSOR SIGNALNOTE:For the diagnostic procedure, refer to “DTC C1242 REAR LEFT ABS SENSOR SIGNAL”. Diagnostic Procedure with Diagnostic Trouble Code (DTC) &g ...

Electrical specification
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Control Module I/O SignalELECTRICAL SPECIFICATIONTerminal No.ContentMeasured value and measuring conditionsRemarks1 — — — 2 — — — 3 — — — 4Ignition power supply10 — 13 V (when the ignition switch is ON) — 5GND0 V (always) ...