VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC C1562 REVERSE ON FAULT
DTC detecting condition:
Abnormal reverse signal
Trouble symptom:
Hill start assist does not operate.
Wiring diagram:
Back-up light system Back-up Light System">
CAN communication system CAN Communication System">
STEP | CHECK | YES | NO |
1.CHECK LAN SYSTEM.
Perform the diagnosis for LAN system. Basic Diagnostic Procedure">
Is there any fault in LAN system?
Perform the diagnosis according to DTC for LAN system. List of Diagnostic Trouble Code (DTC)">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1562 REVERSE ON FAULT">Go to Step 2.
2.CHECK REVERSE SIGNAL USING SUBARU SELECT MONITOR.
1) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">
2) Read the «Reverse Signal» displayed on display.
Is “OFF” displayed when the shift lever is placed in any position other than reverse, and is “ON” displayed in reverse position?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1562 REVERSE ON FAULT">Go to Step 5.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1562 REVERSE ON FAULT">Go to Step 3.
3.CHECK BACK-UP LIGHT ILLUMINATION.
1) Turn the ignition switch to ON.
2) Place the shift lever in reverse position.
Does the back-up light illuminate?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1562 REVERSE ON FAULT">Go to Step 4.
Repair the back-up light circuit.
4.CHECK HARNESS BETWEEN BODY INTEGRATED UNIT AND BACK-UP LIGHT SWITCH (CHECK FOR OPEN CIRCUIT).
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from body integrated unit and back-up light switch.
3) Measure the resistance of harness between body integrated unit and back-up light switch connector.
Connector & terminal
(B281) No. 12 — (B24) No. 1:
Is the resistance less than 1 ??
Replace the back-up light switch. Switches and Harness">
Repair the harness between body integrated unit and back-up light switch connector.
5.CHECK VDCCM&H/U.
1) Connect all connectors.
2) Perform the Clear Memory Mode. Clear Memory Mode">
3) Perform the Inspection Mode. Inspection Mode">
4) Read the DTC. Read Diagnostic Trouble Code (DTC)">
Is the same DTC displayed?
Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1562 REVERSE ON FAULT">Go to Step 6.
6.CHECK DETECTION OF OTHER DTCS FOR VDC.
Read Diagnostic Trouble Code (DTC)">
Is any other DTC displayed?
Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">
Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.
Average vehicle speed
U.S.-spec. models
Except U.S.-spec. models
This display shows the average vehicle
speed since the trip meter was last reset.
Trip knob
Pressing the trip knob toggles the display
between the average vehicle speed corresponding
to the A trip meter display and
the average veh ...
Installation
EXHAUST(H4DO) > Rear Exhaust PipeINSTALLATION1. Apply a coat of spray type lubricant to the mating area of cushion rubber.2. Install the rear exhaust pipe to cushion rubber.NOTE:After assembling, degrease the lubricant which was applied to the cushion rubber while removing/installing.3. Install t ...
About HD RadioTM technology (if
equipped)
HD RadioTM Technology is the digital
evolution of analog AM/FM radio. Your
radio product has a special receiver which
allows it to receive digital broadcasts
(where available) in addition to the analog
broadcasts it already receives. Digital
broadcasts have better sound quality than
analog br ...