Subaru Crosstrek Service Manual: Dtc c1542 clutch switch on malfunction

DTC detecting condition:

Abnormal clutch signal

Trouble symptom:

Hill start assist does not operate.

NOTE:

Depending on the user clutch operation patterns, the hill start assist warning light may illuminate for a while, and then go off.

Illumination condition:

While the vehicle speed is 10 km/h (6 MPH) or above, and the clutch switch signal ON (depressed) condition continues five minutes or more, if the vehicle speed lowers to 10 km/h (6 MPH) or below, the module judges as abnormal (clutch switch stuck ON), and then turns on the warning light.

Turning off condition:

If the clutch switch signal OFF (foot released) condition continues for 2 seconds, the module turns off the warning light.

The hill start assist function does not operate, while the warning light illuminates.

1.CHECK LAN SYSTEM.

Perform the diagnosis for LAN system. Basic Diagnostic Procedure">

Is there any fault in LAN system?

Perform the diagnosis according to DTC for LAN system. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1542 CLUTCH SWITCH ON MALFUNCTION">Go to Step 2.

2.CHECK CLUTCH SIGNAL USING SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Data monitor”. Subaru Select Monitor > OPERATION">

2) Read the «Clutch Switch» displayed on display.

Is “OFF” displayed when the clutch pedal is not depressed, and is “ON” displayed when depressed?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1542 CLUTCH SWITCH ON MALFUNCTION">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1542 CLUTCH SWITCH ON MALFUNCTION">Go to Step 3.

3.CHECK CLUTCH SIGNAL OF ECM USING SUBARU SELECT MONITOR.

1) Using the Subaru Select Monitor, select “Data monitor” in ECM. Subaru Select Monitor > OPERATION">

2) Read the «Clutch Switch» displayed on display.

Is “OFF” displayed when the clutch pedal is not depressed, and is “ON” displayed when depressed?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1542 CLUTCH SWITCH ON MALFUNCTION">Go to Step 5.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1542 CLUTCH SWITCH ON MALFUNCTION">Go to Step 4.

4.CHECK HARNESS BETWEEN ECM AND CLUTCH SWITCH (CHECK FOR OPEN CIRCUIT).

1) Turn the ignition switch to OFF.

2) Disconnect the connectors from ECM and clutch switch.

3) Measure the resistance of harness between ECM and clutch switch connector.

Connector & terminal

(B137) No. 15 — (B107) No. 2:

Is the resistance less than 1 ??

Repair the power supply circuit of clutch switch. Or replace the clutch switch. Clutch Switch">

Repair the harness between ECM and clutch switch connector.

5.CHECK VDCCM&H/U.

1) Connect all connectors.

2) Perform the Clear Memory Mode. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM only. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C1542 CLUTCH SWITCH ON MALFUNCTION">Go to Step 6.

6.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c1541 clutch switch off malfunction

Dtc u0422 invalid data received from body control module

Other materials:

Dtc u0140 lost communication with body control module
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0140 LOST COMMUNICATION WITH BODY CONTROL MODULENOTE:Refer to “LAN SYSTEM (DIAGNOSTICS)” for diagnostic procedures. Basic Diagnostic Procedure">1. OUTLINE OF DIAGNOS ...

Basic diagnostic procedure Procedure
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Basic Diagnostic ProcedurePROCEDURECAUTION:Remove foreign matter (dust, water, oil etc.) from the VDCCM&H/U connector during removal and installation.NOTE:• To check the harness for open or short circuits, shake problem spot or connector.&b ...

Inspection
EyeSight > Relay and FuseINSPECTION1. CHECK FUSE1. Remove the fuse and inspect visually.2. If the fuse is blown out, replace the fuse.NOTE:If the fuse is blown again, check the system wiring harness.2. CHECK RELAY1. Measure the resistance between relay terminals.Terminal No.Inspection conditionsS ...