Subaru Crosstrek Service Manual: Dtc c0071 no signal from steering angle sensor

DTC detecting condition:

Communication from steering angle sensor is faulty.

Trouble symptom:

• VDC does not operate.

• EyeSight does not operate.

1.CHECK POWER SUPPLY FOR STEERING ANGLE SENSOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from steering angle sensor.

3) Turn the ignition switch to ON.

4) Measure the voltage between steering angle sensor and chassis ground.

Connector & terminal

(B231) No. 4 (+) — Chassis ground (−):

Is the voltage 10 — 15 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0071 NO SIGNAL FROM STEERING ANGLE SENSOR">Go to Step 2.

Repair the steering angle sensor power supply circuit.

2.CHECK GROUND CIRCUIT OF STEERING ANGLE SENSOR (CHECK FOR OPEN CIRCUIT).

Measure the resistance between steering angle sensor and chassis ground.

Connector & terminal

(B231) No. 1 — Chassis ground:

Is the resistance less than 10 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0071 NO SIGNAL FROM STEERING ANGLE SENSOR">Go to Step 3.

Repair ground circuit in the steering angle sensor.

3.CHECK VDCCM&H/U.

1) Turn the ignition switch to OFF.

2) Connect all connectors.

3) Perform the Clear Memory Mode. Clear Memory Mode">

4) Perform the Inspection Mode. Inspection Mode">

5) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0071 NO SIGNAL FROM STEERING ANGLE SENSOR">Go to Step 4.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0071 NO SIGNAL FROM STEERING ANGLE SENSOR">Go to Step 5.

4.CHECK VDCCM&H/U.

1) Turn the ignition switch to OFF.

2) Replace the steering angle sensor. Steering Angle Sensor">

3) Perform the Clear Memory Mode. Clear Memory Mode">

4) Perform the Inspection Mode. Inspection Mode">

5) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0071 NO SIGNAL FROM STEERING ANGLE SENSOR">Go to Step 6.

5.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

6.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Original steering angle sensor malfunction

Dtc c0057 vdc interrupted due to egi reason

Dtc c0074 master cylinder pressure sensor output

Other materials:

Removal
CONTROL SYSTEMS > AT Shift Lock Solenoid and “P” Range SwitchREMOVAL1. SOLENOID UNIT1. Remove the AT select lever. Select Lever > REMOVAL">2. Remove the spacer and gasket. Select Lever > DISASSEMBLY">3. Using a flat tip screwdriver with a thin tip, remove the h ...

Installation
POWER ASSISTED SYSTEM (POWER STEERING) > Steering WheelINSTALLATIONCAUTION:• Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">• If the steering w ...

To arm the system using the keyless access function (if equipped)
1. Close all windows and the moonroof (if equipped) 2. Turn the push-button ignition switch to the "OFF" position. 3. Open the doors and get out of the vehicle. 4. Make sure that the engine hood is locked. 5. Close all doors and the rear gate. Door lock sensor Security i ...