Subaru Crosstrek Service Manual: Dtc c0054 bls off malfunction

DTC detecting condition:

Defective stop light switch

Trouble symptom:

• VDC does not operate.

• EyeSight does not operate.

1.CHECK STOP LIGHT SWITCH.

Check the stop light switch. Stop Light Switch > INSTALLATION">

Is the check result OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0054 BLS OFF MALFUNCTION">Go to Step 2.

Adjust the installation position of the stop light switch. Stop Light Switch > INSTALLATION">

2.CHECK STOP LIGHT SWITCH.

1) Turn the ignition switch to OFF.

2) Disconnect the stop light switch connector.

3) Measure the resistance of stop light switch terminals.

Terminals

No. 3 — No. 4:

Is the resistance less than 1 ? when the stop light switch is ON (when pedal is depressed)?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0054 BLS OFF MALFUNCTION">Go to Step 3.

Replace the stop light switch. Stop Light Switch">

3.CHECK STOP LIGHT RELAY.

Measure the resistance of stop light relay terminals.

Terminals

No. 7 — No. 10:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0054 BLS OFF MALFUNCTION">Go to Step 4.

Replace the stop light relay.

4.CHECK VDCCM&H/U CONNECTOR.

Disconnect the connector from the VDCCM&H/U.

Is there poor contact or damage of the VDCCM&H/U connector?

Repair the VDCCM&H/U connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0054 BLS OFF MALFUNCTION">Go to Step 5.

5.CHECK STOP LIGHT SWITCH CIRCUIT.

Measure the resistance of stop light switch circuit.

Connector & terminal

(B310) No. 16 — (B567) No. 10:

(B65) No. 4 — (B567) No. 7:

(B65) No. 3 — (F/B fuse) No. 8:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0054 BLS OFF MALFUNCTION">Go to Step 6.

Repair the stop light switch circuit.

6.CHECK STOP LIGHT SWITCH CIRCUIT.

1) Connect all connectors.

2) Turn the ignition switch to ON.

3) Measure the voltage between stop light relay and chassis ground.

Connector & terminal

(B567) No. 10 (+) — Chassis ground (−):

Is the voltage 10 V or more when the stop light switch is ON (when pedal is depressed)?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0054 BLS OFF MALFUNCTION">Go to Step 7.

Repair the stop light switch circuit.

7.CHECK VDCCM&H/U.

1) Perform the Clear Memory Mode. Clear Memory Mode">

2) Perform the Inspection Mode. Inspection Mode">

3) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0054 BLS OFF MALFUNCTION">Go to Step 8.

8.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c0054 bls on malfunction

Dtc c0081 system failure

Other materials:

Dtc c0057 ecm communication circuit
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0057 ECM COMMUNICATION CIRCUITDTC detecting condition:No CAN signal from ECM.Trouble symptom:• VDC does not operate.• EyeSight does not operate.STEPCHECKYESNO1.CHECK LAN SYSTEM.P ...

Driving tips for AWD models
WARNING Always maintain a safe driving speed according to the road and weather conditions in order to avoid having an accident on a sharp turn, during sudden braking or under other similar conditions. Always use the utmost care in driving - overconfidence because you are driving ...

Jump starting
WARNING Battery fluid is SULFURIC ACID. Do not let it come in contact with the eyes, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush the exposed area with water immediately. Get medical help if the fluid has entered your eyes. If battery flui ...