Subaru Crosstrek Service Manual: Dtc c0027 rear left abs sensor circuit open or short

DTC detecting condition:

• Defective ABS wheel speed sensor (broken wire, input voltage too high)

• Defective harness connector

• ABS does not operate.

• VDC does not operate.

• EyeSight does not operate.

1.CHECK POOR CONTACT OF CONNECTOR.

Check if there is poor contact between VDCCM&H/U and ABS wheel speed sensor.

Is there poor contact?

Repair the connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0027 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORT">Go to Step 2.

2.CHECK HARNESS CONNECTOR BETWEEN VDCCM&H/U AND ABS WHEEL SPEED SENSOR (CHECK FOR OPEN CIRCUIT).

1) Turn the ignition switch to OFF.

2) Disconnect the connector (B310) from the VDCCM&H/U.

3) Disconnect the connector from ABS wheel speed sensor.

4) Measure the resistance between VDCCM&H/U connector and ABS wheel speed sensor connector.

Connector & terminal

DTC C0021

(B310) No. 6 — (B6) No. 1:
(B310) No. 5 — (B6) No. 2:

DTC C0023

(B310) No. 8 — (B15) No. 1:
(B310) No. 9 — (B15) No. 2:

DTC C0025

(B310) No. 12 — (R72) No. 1:
(B310) No. 11 — (R72) No. 2:

DTC C0027

(B310) No. 2 — (R73) No. 1:
(B310) No. 3 — (R73) No. 2:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0027 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORT">Go to Step 3.

Repair the harness connector between VDCCM&H/U and ABS wheel speed sensor.

3.CHECK GROUND SHORT OF HARNESS.

Measure the resistance between VDCCM&H/U connector and chassis ground.

Connector & terminal

DTC C0021

(B310) No. 6 — Chassis ground:

DTC C0023

(B310) No. 8 — Chassis ground:

DTC C0025

(B310) No. 12 — Chassis ground:

DTC C0027

(B310) No. 2 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0027 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORT">Go to Step 4.

Repair the harness connector between VDCCM&H/U and ABS wheel speed sensor.

4.CHECK ABS WHEEL SPEED SENSOR POWER SUPPLY CIRCUIT.

1) Connect the VDCCM&H/U connector.

2) Turn the ignition switch to ON.

3) Measure the voltage between ABS wheel speed sensor connector and chassis ground.

Connector & terminal

DTC C0021

(B6) No. 2 (+) — Chassis ground (−):

DTC C0023

(B15) No. 2 (+) — Chassis ground (−):

DTC C0025

(R72) No. 2 (+) — Chassis ground (−):

DTC C0027

(R73) No. 2 (+) — Chassis ground (−):

Is the voltage 5 — 16 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0027 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORT">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0027 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORT">Go to Step 5.

5.CHECK VDCCM&H/U POWER SUPPLY CIRCUIT.

1) Turn the ignition switch to OFF.

2) Disconnect the VDCCM&H/U connector.

3) Turn the ignition switch to ON.

4) Measure the voltage between VDCCM&H/U connector terminals.

Connector & terminal

(B310) No. 1 (+) — (B310) No. 26 (−):

(B310) No. 14 (+) — (B310) No. 26 (−):

(B310) No. 20 (+) — (B310) No. 26 (−):

Is the voltage 10 — 15 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0027 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORT">Go to Step 6.

Check the generator, battery and VDCCM&H/U power supply circuit.

6.CHECK ABS WHEEL SPEED SENSOR SIGNAL.

1) Prepare an oscilloscope.

2) Check the ABS wheel speed sensor. Front ABS Wheel Speed Sensor > INSPECTION"> Rear ABS Wheel Speed Sensor > INSPECTION">

Does the oscilloscope indicate the waveform pattern as shown in the figure?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0027 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORT">Go to Step 7.

Replace the ABS wheel speed sensor. Front ABS Wheel Speed Sensor"> Rear ABS Wheel Speed Sensor">

7.CHECK VDCCM&H/U.

1) Connect all connectors.

2) Perform the Clear Memory Mode. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0027 REAR LEFT ABS SENSOR CIRCUIT OPEN OR SHORT">Go to Step 8.

8.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c0026 rear right abs sensor signal

Dtc c0028 rear left abs sensor signal

Other materials:

Dtc p0336 crankshaft position sensor "a" circuit range/performance
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0336 CRANKSHAFT POSITION SENSOR "A" CIRCUIT RANGE/PERFORMANCEDTC detecting condition:Detected when two consecutive driving cycles with fault occur.Trouble symptom:• Engine stall• Failure ...

Caution
POWER ASSISTED SYSTEM (POWER STEERING) > General DescriptionCAUTION• Wear appropriate work clothing, including a helmet, protective goggles and protective shoes when performing any work.• Before removal, installation or disassembly, be sure to clarify the failure. Avoid unnecessary re ...

Vehicle activation status screen
When the vehicle stops 1) Steering axle When the vehicle is being driven regularly 1) Power train (illuminated in blue) When the Vehicle Dynamics Control system is being activated: the tires illuminate in yellow. 1) History of Vehicle Dynamics Control system activation When ...