Subaru Crosstrek Service Manual: Dtc b2a0d airbag signal

Diagnosis start condition:

When ignition switch is ON.

DTC detecting condition:

Either the regular signal or collision signal cannot be detected from the airbag CM for at least 30 seconds.

Trouble symptom:

• ACN function does not operate.

• RED LED illuminates.

For the coupling connector, refer to “WIRING SYSTEM”.

• CommCheck is required after replacing the DCM. Telematics System > OPERATION">

• Before performing diagnosis, refer to “CAUTION” in “General Description” in Airbag System. General Description > CAUTION">

1.CHECK DTC.

Read the DTC. Diagnostic Code(s) Display">

Is DTC B2A0D displayed? (Current malfunction)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0D AIRBAG SIGNAL">Go to Step 2.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.CHECK DTC.

Read DTC of the airbag. Read Diagnostic Trouble Code (DTC)">

Is DTC displayed? (Current malfunction)

Perform the diagnosis according to DTC.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0D AIRBAG SIGNAL">Go to Step 3.

3.CHECK HARNESS (OPEN CIRCUIT).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the airbag CM connector.

3) Disconnect the DCM connector.

4) Measure the resistance between airbag CM connector and DCM connector.

CAUTION:

To measure the voltage and resistance of airbag system component, be sure to use the specified test harness. General Description">

Connector & terminal

(i270) No. 18 — (AB6) No. 24:

Is the resistance 1 ? or less?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0D AIRBAG SIGNAL">Go to Step 4.

Repair or replace the open circuit of harness.

4.CHECK HARNESS (GROUND SHORT CIRCUIT).

Measure the resistance between DCM connector and chassis ground.

Connector & terminal

(i270) No. 18 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0D AIRBAG SIGNAL">Go to Step 5.

Repair or replace the short circuit of the harness.

5.CHECK THE CONNECTOR (SHORT CIRCUIT TO POWER SUPPLY).

Measure the voltage between DCM connector and chassis ground.

Connector & terminal

(i270) No. 18 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Replace the DCM. Data Communication Module">

Repair or replace the short circuit of the harness.

Dtc b2a0c dcm internal fault

Dtc b2a0e mute line circuit

Other materials:

Connecting a Bluetooth device
To use the Bluetooth audio system, it is necessary to register a Bluetooth device with the system. Registering an additional device 1. Select the "Add" key on the Bluetooth devices connection screen. 2. For more information: Refer to "Registering/ connecting Bluetoothdevice" F5- 65. Se ...

Installation
PARKING BRAKE > Parking Brake LeverINSTALLATION1. Install each part in the reverse order of removal.CAUTION:• The front seat mounting bolts differ between the front mounting points and the rear mounting points. When installing the front seat, make sure that you are using correct bolts at co ...

Removal
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Switches and HarnessREMOVAL1. BACK-UP LIGHT AND NEUTRAL POSITION SWITCH1. Disconnect the ground cable from battery.2. Remove the clip (A) from the air intake boot.3. Loosen the clamp (B) connecting the air intake boot and air cleaner case (rear).4. Loos ...