Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc b2a0b green led circuit

TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC B2A0B GREEN LED CIRCUIT

Diagnosis start condition:

When ACC is ON.

DTC detecting condition:

Current in LED is less than 1 mA. (Improper LED connection, etc.)

Current is more than 200 mA for at least 50 ms. (Short-circuited LED, etc.)

Trouble symptom:

RED LED illuminates.

Wiring diagram:

NOTE:

For the coupling connector, refer to “WIRING SYSTEM”.

Telematics Telematics System > WIRING DIAGRAM">

CAUTION:

CommCheck is required after replacing the DCM. Telematics System > OPERATION">

STEPCHECKYESNO

1.CHECK DTC.

Read the DTC. Diagnostic Code(s) Display">

Is DTC B2A0B displayed? (Current malfunction)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0B GREEN LED CIRCUIT">Go to Step 2.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.PERFORM THE SYSTEM OPERATION CHECK.

Perform [GREEN LED Lighting] in the system operation check mode. System Operation Check Mode">

Does the GREEN LED illuminate?

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0B GREEN LED CIRCUIT">Go to Step 3.

3.CHECK HARNESS (OPEN CIRCUIT).

1) Turn the ignition switch to OFF.

2) Disconnect the telematics button connector.

3) Disconnect the DCM connector.

4) Measure the resistance between telematics button connector and DCM connector.

Connector & terminal

(i270) No. 3 — (AD2) No. 4:

(AD2) No. 1 — Chassis ground:

Is the resistance 1 ? or less?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0B GREEN LED CIRCUIT">Go to Step 4.

Repair or replace the open circuit of harness.

4.CHECK HARNESS (GROUND SHORT CIRCUIT).

Measure the resistance between DCM connector and chassis ground.

Connector & terminal

(i270) No. 3 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0B GREEN LED CIRCUIT">Go to Step 5.

Repair or replace the short circuit of the harness.

5.CHECK THE CONNECTOR (SHORT CIRCUIT TO POWER SUPPLY).

Measure the voltage between DCM connector and chassis ground.

Connector & terminal

(i270) No. 3 (+) — Chassis ground (−):

(AD2) No. 1 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A0B GREEN LED CIRCUIT">Go to Step 6.

Repair or replace the short circuit of the harness.

6.CHECK THE TELEMATICS BUTTON (LED) UNIT.

Measure the resistance of the telematics button (LED) unit.

Terminals

No. 4 — No. 1:

Is there continuity?

Replace the DCM. Data Communication Module">

Replace the telematics button. Switches and Harness">

Dtc b2a0a red led circuit
TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2A0A RED LED CIRCUITDiagnosis start condition:When ACC is ON.DTC detecting condition:• Current in ...

Dtc b2a0c dcm internal fault
TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2A0C DCM INTERNAL FAULTDIAGNOSIS START CONDITION:When ignition switch is ON.DTC DETECTING CONDITION:&bu ...

Other materials:

Wiring diagram
CONTROL SYSTEMS > AT Shift Lock Control SystemWIRING DIAGRAM1. MODEL WITHOUT PUSH BUTTON IGNITION SWITCH(1)Ignition switch(5)TCM (shift range information)(9)Battery(2)Stop light and brake switch(6)Key lock solenoid(10)ECM (delivery (test) mode signal)(3)Key warning switch(7)Shift lock solenoid(11 ...

Inspection
WIPER AND WASHER SYSTEMS > Relay and FuseINSPECTION1. CHECK FUSE1. Remove the fuse and inspect visually.2. If the fuse is blown out, replace the fuse.2. CHECK RELAY1. Check the resistance between relay terminals.Terminal No.Inspection conditionsStandardCircuit1 — 2Always1 M? or more1 — 2Apply ...

Wiring diagram
ENTERTAINMENT > Rearview Camera SystemWIRING DIAGRAMRefer to “Rearview Camera System” in the wiring diagram.– 6.2 inch display: Rearview Camera System > WIRING DIAGRAM">– 7 inch display: Rearview Camera System > WIRING DIAGRAM"> ...

© 2016-2024 Copyright www.sucross.com