Subaru Crosstrek Service Manual: Dtc b2a06 right speaker/audio circuit

Diagnosis start condition:

When ACC is ON.

DTC detecting condition:

Speaker impedance is more than 10 k? for 100 ms. (Detached speaker connection, etc.)

Trouble symptom:

• Call function cannot be used.

• RED LED illuminates.

For the coupling connector, refer to “WIRING SYSTEM”.

CommCheck is required after replacing the DCM. Telematics System > OPERATION">

1.CHECK DTC.

Read the DTC. Diagnostic Code(s) Display">

Is DTC B2A06 displayed? (Current malfunction)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A06 RIGHT SPEAKER/AUDIO CIRCUIT">Go to Step 2.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.PERFORM THE SYSTEM OPERATION CHECK.

Perform [Speaker ON] in the system operation check mode. System Operation Check Mode">

Does it sound?

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A06 RIGHT SPEAKER/AUDIO CIRCUIT">Go to Step 3.

3.CHECK HARNESS (OPEN CIRCUIT).

1) Turn the ignition switch to OFF.

2) Disconnect the speaker connector and tweeter connector.

3) Disconnect the DCM connector.

4) Measure the resistance between speaker connector and tweeter connector and DCM connector.

Connector & terminal

(i271) No. 4 — (D12) No. 2:
(i271) No. 4 — (i159) No. 1:
(i271) No. 12 — (D12) No. 1:
(i271) No. 12 — (i159) No. 3:

Is the resistance 1 ? or less?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A06 RIGHT SPEAKER/AUDIO CIRCUIT">Go to Step 4.

Repair or replace the open circuit of harness.

4.CHECK HARNESS (GROUND SHORT CIRCUIT).

Measure the resistance between DCM connector and chassis ground.

Connector & terminal

(i271) No. 4 — Chassis ground:
(i271) No. 12 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A06 RIGHT SPEAKER/AUDIO CIRCUIT">Go to Step 5.

Repair or replace the short circuit of the harness.

5.CHECK THE CONNECTOR (SHORT CIRCUIT TO POWER SUPPLY).

Measure the voltage between DCM connector and chassis ground.

Connector & terminal

(i271) No. 4 (+) — Chassis ground (−):
(i271) No. 12 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2A06 RIGHT SPEAKER/AUDIO CIRCUIT">Go to Step 6.

Repair or replace the short circuit of the harness.

6.CHECK THE SPEAKER.

Perform the inspection of speaker unit and tweeter unit. Front Speaker"> Rear Speaker">

Are the speaker and tweeter OK?

Replace the DCM. Data Communication Module">

Replace the speaker and tweeter. Front Speaker"> Rear Speaker">

Dtc b2a05 left speaker/audio circuit

Dtc b2a08 sos button circuit

Other materials:

Dtc c0045 tcm malfunction
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0045 TCM MALFUNCTIONDTC detecting condition:Defective TCMTrouble symptom:• ABS does not operate.• VDC does not operate.• EyeSight does not operate.STEPCHECKYESNO1.CHECK CVT ...

Installation
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF) > SunshadeINSTALLATIONCAUTION:For installation of the stereo camera cover assembly, refer to “INSTALLATION”, “Stereo Camera” in the “EyeSight” section and observe the precautions for installation. Stereo Camera > INST ...

Note Note
NOTENOTEThis information will improve the efficiency of maintenance and assure the sound work.1. CLEANING• Perform the operation in a clean location and use extra caution in dust proofing.• Clean the items (except for assembly components) with steam, etc. before disassembly. During steam ...